Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
Avoid striking, shading etc. • Do not use strong or abrasive detergents when cleaning the unit. Do use dry cloth to clean the unit when dirty. In case the dirt is hard to remove, use mild detergent and wipe gently. * Do not expose the unit to rain or moisture. Do take immediate action if ever the unit do become wet. Turn power off and refer servicing to qualified service personnel. Moisture can damage the unit and also create the danger of electronic shock. • Use the unit under the conditions where temperature is within 23°F - 113°F (—5°C - +45°C) and humidity is less than 90'/.. - 2 - MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS miÆBffi Pannonie “o' O | o ® o] < *v.*cS0D C=3 su <§> © © © ©@ © © © © © © © © 111. Power Switch (POWER, ON/OFF) This switch turns on and off the power of the Remote Control Unit (RCU). 112. Power Indicator This switch lights red whenever the unit is operating. 113. Luminance Gain Fine Control (Y ADJUST) This control allows for fine adjustment of the luminance signal level for matching the levels of ail cameras in a system. Adjust this control only after having set the Cable Length Compensation Switch (115) to the correct position. 114. Chroma Gain Fine Control (CHROMA ADJUST) This control allows for fine adjustment of the chroma signal level for matching the chroma levels of all the cameras in a system. Adjust this control only after having set the Cable Length Compensation Switch (115) to the correct position. 115. Cable Length Compensation Switch (CABLE/COMP) This switch is used to compensate for extensive cable lengths used with the 26-pin multi-cable between the camera and Remote Control Unit (RCU). 1. Use for cable length of less than 225 ft (75m) 2. Use for cable length of 225-450 ft (75-150m) 3. Use for cable length of 450-690 ft (15G-230m) 4. Use for cable length of 690-900 ft (230-300) This switch is also used to compensate for extensive cable lengths used with the coaxial cable (5C-2V) between the camera and Remote Control Unit (RCU). 1. Use for cable length of less than 450 ft (150m) 2. Use for cable length of 450-1000ft (150-300m) 3. Not available 4. Not available - 3 - 116. Cable Indicator (CABLE, MULTl/MPX) This indicator shows the setting position of the Cable Selection Switch (152) on the rear panel. 117. Remote Control Box (RCB) Operation Switch (RCB) When connecting the Remote Control Box to the camera without using the Remote Control Unit, set this switch to ON position. When the RCB is installed in the RCU this switch is inoperative. 118. Remote Control Box (RCB) Indicator (ON/OFF) This indicator lights while control data is communicated between the camera and Remote Control Unit (RCU) or Remote Control Box (RCB). 119. High Gain Selection Switch (0 dB/+9 dB/+18 dB) Normally set this switch to the 0 dB position. Positions +9 dB and +18 dB increase the video output amplitude for dark scenes and are equivalent to opening the lens iris 1.5 or 3 F-steps, respectively. 120. 6dB Gain Selection Switch (+6 dB/OFF/—6 dB) Normally set this switch to OFF position, By the combination of this switch with the High Gain Selection Switch (119), fine adjustment of the gain level is available. 121. Color Bar/Camera Selection Switch (BAR/CAM) In a system configuration, this switch is used for signal selection between camera mode and color bar mode. BAR: A color bar signal is provided from the Video Output Connector (146) on the Remote Control Unit (RCU), CAM: The actual picture, as picked up through the lens, is displayed. 122. Detail Level Selection Switch (DTL, LEVEL-HIGH/LOW/OFF) The detail/aperture level can be selected by this switch in three steps. Set this switch to the desired position while observing the sharpness of the picture. 123. Red and Blue Gain Controls (R GAIN/B GAIN) These controls are used to manually adjust the white balance. These controls only work when the White/Black Balance Selection Switch (126) is set to the MANU position. Turn the controls clockwise to increase the red and blue signal levels, and counterclockwise to decrease these levels. Note: As these controls employ Digital Processing, the Red and Blue signal levels will be changed in discrete steps. 124. Red and Blue Pedestal Level Controls (PED, R/B) The black balance can be set manually by these controls when the White/Black Balance Selection Switch (126) is set to the MANU position. Turn these controls clockwise to increase the red and blue pedestal levels, and counterclockwise to decrease the levels. Note: As these controls employ the Digital Processing, these levels will be changed in the steps. 125. Total Pedestal Level Control (TOTAL PEDESTAL) This control can adjust the pedestal level of the video signal (luminance) for matching the black level between two or more cameras in a system. Turn this control clockwise to increase the pedestal level, and counterclockwise to decrease the level. Note: As this control employs the Di...