Assessments - 0, GPA: 0 ( )

Fabricante : Philips Arquivo Tamanho: 723.19 kb Arquivo Nome : Língua de Ensino:

Reproduction in whole or in part is prohibited without prior consent of the copyright owner. Royal Philips Electronics is not liable for omissions or for technical or editorial errors in this manual or for damages directly or indirectly resulting from the use of the RFX6500 / SBC LI910 RF Extender. The information in this user guide may be subject to change without prior notice. All brand or product names are trademarks or registered trademarks of their respective companies or organizations. EN User Guide 1 Contents Contents 2 How to Use the RF Extender 3 Introduction 3 How to Install the RF Extender 5 How to Connect the RF Extender 5 How to Position the Blaster Unit 6 How to Install the Dual IR Emitters 7 How to Position the Receiver Unit 9 How to Do More 12 How to Set the Extender IDs 12 How to Avoid Interference from Other Prontos 13 How to Use a Longer Connection Cable 13 How to Fine-Tune the Installation Using the Dip Switches 14 How to Turn Off the IR Blaster 14 How to Set the Dual IR Emitter Power Levels 14 Troubleshooting 16 Specifications 17 User Guide 2 How to Use the RF Extender Introduction Infrared (IR) remote controls do not work properly when obstacles between the remote control and the audio/video devices disturb the operating signal. This problem can be solved using radio frequency (RF) as a carrier for IR commands. The Pronto Remote Control, in combination with the RF Extender, can operate audio/video devices from virtually any location. The RF Extender consists of two units: a Receiver unit, and a Blaster unit. The Receiver unit receives RF signals sent out by the Pronto Remote Control. This unit is connected to the Blaster unit, which converts the signals into IR signals. The Blaster unit then transmits the IR signals to the audio/video devices. EN Pronto Receiver unit Blaster unit RF signals IR signals When the Blaster unit cannot reach all devices or transmits with too much power, you can use the included Dual IR emitters. You can set up the Dual IR emitters in two ways: ¦ The Dual IR emitters in combination with the Blaster unit. When there is limited space around the IR receivers of the devices, for instance in a small closet. ¦ The Dual IR emitters instead of the Blaster unit. When you want to transmit IR signals very accurately, you turn off the Blaster unit, and control the devices by using the Dual IR emitters alone. User Guide 3 How to Use the RF Extender Situation A: Your devices can be remotely controlled when they are not in the line of sight of the remote control. Situation C: The RF Extender is placed inside a closet, a rack or another piece of furniture together with your devices. Situation B: The RF Extender controls devices placed in an adjacent room. Situation A: Your devices can be remotely controlled when they are not in the line of sight of the remote control. Situation C: The RF Extender is placed inside a closet, a rack or another piece of furniture together with your devices. Situation B: The RF Extender controls devices placed in an adjacent room. The arrangements in the situation shown above can also be combined. You can control all RF Extenders individually with one or more Pronto Remote Controls. User Guide 4 User Guide 5 EN How to Install the RF Extender Make sure you have the following components: RF Extender Receiver unit, RF Extender Blaster unit, power adapter, connection cable, Dual IR emitters and screws. The installation of the RF Extender consists of 4 main steps: ¦ Connecting the RF Extender; ¦ Positioning the Blaster unit; ¦ Installing the Dual IR emitters; ¦ Positioning the Receiver unit. How to Connect the RF Extender 1 Plug the power cable into the Blaster unit. 2 Plug the power adapter into the mains wall socket. When connected, a red LED on the Blaster unit will start blinking. After a few seconds, the LED will stop blinking and stay on. Remark The LED on the Blaster unit will also blink when the Blaster unit sends out IR signals to the audio/video devices. 3 Plug the connection cable into the Blaster unit until it clicks. 4 Plug the connection cable into the Receiver unit until it clicks. When connected, the LED on the Receiver unit will stay on for 3 seconds. Afterwards, the LED will go off. User Guide 5 EN How to Install the RF Extender Make sure you have the following components: RF Extender Receiver unit, RF Extender Blaster unit, power adapter, connection cable, Dual IR emitters and screws. The installation of the RF Extender consists of 4 main steps: ¦ Connecting the RF Extender; ¦ Positioning the Blaster unit; ¦ Installing the Dual IR emitters; ¦ Positioning the Receiver unit. How to Connect the RF Extender 1 Plug the power cable into the Blaster unit. 2 Plug the power adapter into the mains wall socket. When connected, a red LED on the Blaster unit will start blinking. After a few seconds, the LED will stop blinking and stay on. Remark The LED on the Blaster unit will also blink when the Blaster unit sends out IR signals to the audio/v...

Baixe o seu

Para fazer o download, introduza 2 dígitos :