Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
ENGLISH Setting the remote control This is only necessary if your TV does not respond to the SRU 1018. If that is the case, the SRU 1018 does not recognize the brand and/or model of your TV and you need to program the remote control to do so. The example below instructs you how to do this. You can set the remote control either manually or automatically. Manually setting the remote control 1 Turn on the TV manually or use the original remote control. Tune in to channel 1. 2 Look up the brand of your TV in the code list at the back of this manual. One or more 3-figure key codes are shown for each brand. Note the first code. On our website you can directly select your device typenumber to find the right code. Make sure you use the codes from the correct table. 3 Keep keys 1 and 3 on the SRU 1018 pressed simultaneously for five seconds until the indicator light remains lit. 4 Then enter the code noted in step 2 using the code keys. – The indicator light will now flash twice. If the indicator light flashes once for an extended period, the code has not been entered properly or the wrong code has been entered. Star t again from step 2. 5 Point the SRU 1018 at the TV and check that it responds as it should. – If the TV responds to all of the key commands, the SRU 1018 is ready for use. Do not forget to note your code. • If the device does not respond at all, or not to all of the key commands, start again from step 2 and try the next code from the list. ENGLISH Automatically setting the remote control If you cannot find the right code for your brand device, the remote control can automatically search for the right code. 1 Make sure the TV is switched on and select a channel using the original remote control or the keys on the TV (for example channel 1). 2 Keep keys 1 and 3 on the SRU 1018 pressed simultaneously for five seconds, until the indicator light remains lit. Press the y key of the SRU 1018 and keep it pressed. – The SRU 1018 now star ts emitting all known ‘TV off ’ signals, one by one. Each time a code is sent, the indicator light flashes. 4 When your TV switches off (stand-by), immediately release the y key of the SRU 1018 to confirm. – The SRU 1018 has now found a code that works on your TV. 5 Check if you can operate all functions on your TV with the SRU 1018. • If this is not the case, you can redo the automatic setting. The SRU 1018 will then search for a code that perhaps works better. – After the SRU 1018 has run through all the known codes, the search will stop automatically and the indicator light stops flashing. – Automatic programming of a TV takes a maximum of 6 minutes. ENGLISH 3. Keys and functions The illustration on page 3 gives an overview of all keys and their functions. 1 Indicator light . . . . flashes / lights up when a key / key combination is pressed. 2 a . . . . . . . . . . . . . . . . switches Teletext on. 3 E . . . . . . . . . . . . . . . . selects between regular (4:3) and wide screen (16:9) TV. 4 PROG + . . . . . . . . . . selects a following channel. 5 VOL – . . . . . . . . . . . . reduces the TV volume. 6 PROG –. . . . . . . . . . . selects a previous channel. 7 Digit keys . . . . . . . . . direct choice of channels and other functions. 8 VOL + . . . . . . . . . . . . increases the TV volume. 9 s (Mute) . . . . . . . . . mutes the sound of the TV. 0 I . . . . . . . . . . . . . . . . switches Teletext off. ! y (Standby) . . . . . . . switches the TV on or off. 4. Troubleshooting • Problem – Solution • The device you want to operate does not respond when you press a key. – Replace the old batteries with two new R03, UM4 or AAA type batteries. – Point the SRU 1018 at the device and make sure that there are no obstructions between the SRU 1018 and the device. • The SRU 1018 does not respond properly to commands. – Maybe you are using the wrong code. Tr y programming the SRU 1018 again using another code, which is mentioned under the brand of your device, or reset for automatic search to find the right code. • Your brand of device is not in the code list. – Tr y to set the SRU 1018 automatically. See ‘Automatically setting the remote control’. • None of the codes works during manual setting of the remote control. – If that is the case, follow the instructions under ‘Automatically setting the remote control’. FRANCAIS Sommaire 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2. Installation de la telecommande . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Inser tion des piles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Essai de la telecommande. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Configuration de la te...