Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
One or more four-figure codes are shown for each brand. Note the first code. Be careful! There are separate tables for TV, VCR and DVD. Make sure you use the codes from the correct table. 3 Keep the TV Key pressed for 3 seconds until the green indicator light remains lit. 4 Then enter the code noted in step 2 using the digital keys. – The green indicator light will now flash twice. If the light flashes once for an extended period, the code has not been entered properly or the wrong code has been entered. Star t again from step 2. 5 Point the RU252 at the TV and check that it responds as it should. – If the TV responds to all of the key commands, the RU252 is ready for use. Do not forget to note your code. • If the device does not respond at all, or not to all of the key commands, start again from step 2 and try the next code from the list. 5 Instructions for use RU252ok.qxd:RU252.qxd 17/08/07 15:56 Page 6 RU252ok.qxd:RU252.qxd 17/08/07 15:56 Page 6 English Automatically setting the remote control If you cannot find the right code for your brand device, the remote control can automatically search for the right code. Example of TV: 1 Make sure the TV is switched on and select a channel using the original remote control or the keys on the TV (for example channel 1). The RU252 emits the ‘switch off TV’ signal for all models of TV that are stored in the memory. • If the device is a DVD-player or video recorder, inser t a disk or tape and star t playback. 2 Then keep the TV Key pressed for 3 seconds until the green indicator light remains lit. 3 Press again the the Standby key and Keep it pressed – The RU252 now star ts emitting all known ‘TV off ’ signals, one by one. Each time a code is sent, the green indicator light flashes. 4 When your TV switches of (standby mode) immediately release the standby key of the RU252 -The RU252 has now found a code that works on your TV 5 Check if you can operate all functions on your TV with the RU252. • If this is not the case, you can redo the automatic setting.The RU252 will then search for a code that perhaps works better. – After the RU252 has run through all the known codes, the search will stop automatically and the green light will stop flashing. – Automatic programming of a TV takes a maximum of 5 minutes. For VCR/DVD this time is 6 minutes 6 Instructions for use RU252ok.qxd:RU252.qxd 17/08/07 15:56 Page 7 RU252ok.qxd:RU252.qxd 17/08/07 15:56 Page 7 3. Keys and functions The illustration on page 3 gives an over view of all keys and their functions. 1 y Standby . . . . . . . . . switches TV, VCR or DVD mode on or off. 2 Indicator light . . . . . -lights up green when an IR signal is being sent. -flashes green when a code is being entered and when automatically setting the remote control. 3 TV - VCR/DVD. . . . . select the device you want to operate: TV, VCR or DVD. 4 s (Mute) . . . . . . . . . . mutes the sound of the TV. 5 - PROG + . . . . . . . . . . selects a previous or following channel. 6 (Menu) . . . . . . . . Wide screen: TV Menu on/off: VCR/DVD 7 Digital keys . . . . . . . . direct choice of channels and other functions. 8 SHIFT . . . . . . . . . . . . . for extra functions. When pressed at the same time as a second key, the second key will get another function. For example: SHIFT + PROG+: . . 'menu up' SHIFT + PROG-: . . 'menu down' SHIFT + VOL+: . . . . 'menu right' SHIFT + VOL-: . . . . 'menu left' SHIFT + . . . . . . Menu on/off Tr y out other combinations with the Shift-key on your appliance in order to find out which functions are available. Only functions featured on the original remote control are available. 9 . . . . . . . . . . . . . . . . switches teletext on. 0 5. . . . . . . . . . . . . . . . . . - red teletext key - rewind (VCR/DVD) 9 . . . . . . . . . . . . . . . . . . - green teletext key - stop (VCR/DVD) 0 . . . . . . . . . . . . . . . . . . record (VCR/DVD) ;. . . . . . . . . . . . . . . . . . . - yellow teletext key - pause (VCR/DVD) 6. . . . . . . . . . . . . . . . . . - blue teletext key - wind (VCR/DVD) 2 . . . . . . . . . . . . . . . . . . - white teletext key - play (VCR/DVD) ! . . . . . . . . . . . . . . . . switches teletext off. @ -/--. . . . . . . . . . . . . . . . . selects between one- and two-figure channel numbers. # OK . . . . . . . . . . . . . . . . confirms your selection. $ - VOL + . . . . . . . . . . . . adjusts the TV volume. % AV. . . . . . . . . . . . . . . . . switches between external inputs of your equipment. Note! The VOL – /VOL + and s (Mute) keys give direct access to the TV volume even if you are operating your VCR or DVD equipment. If the device does not respond at all, or not to all of the key commands, follow the instructions under ‘Setting the remote control’. It is possible that you must enter another code for the device. English 7 Mode d'emploi RU252ok.qxd:RU252.qxd 17/08/07 15:56 Page 8 RU252ok.qxd:RU252.qxd 17/08/07 15:56 Page 8 Sommaire Francais 1. Introduction . . . . . . . . . . . . . . . . . . . . . . ....