Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
1 Make sure you have the original remote control at hand. 2 Use SELECT to select the desired device. E.g. DVD. 4 Keep LEARN and the key you wish to learn on the SRU 5170 pressed simultaneously for 3 seconds, ’ lights up, together with ’LEARNING’. 5 Press the key you wish to copy on the original until ‘ remote control. – lights up. The remote control is now learning the function. – When the remote control has learned the function, the display shows ’LEARN OK’ to confirm that the signal is stored. – If the display shows ‘ERROR‘ or ‘MEM FULL’, star t again from step 1. Also see ‘Troubleshooting’ under 6. ‘Suppor t’. Place both remote controls on a flat surface (like a coffee table) and aim them head-to-head with about 5 - 10 cm in between. English 9 Instructions for use English Activating / de-activating the backlight function The backlight illuminates the display so you can clearly see all display messages, even in a dimly lit room. As the backlight consumes additional power, the batter y lifetime will reduce when the backlight is used frequently. Therefore it is possible to de-activate the backlight function. De-activating the backlight function • Keep digit keys 1 and 9 pressed simultaneously for three seconds. – The backlight function is now de-activated and the backlight cannot be turned on. Activating the backlight function • Keep digit keys 7 and 9 pressed simultaneously for three seconds. – The backlight function is now activated and the backlight can be turned on. Restoring the original functions of the remote control In some cases it could be useful to restore the original functions of the remote control. E.g. if the remote control memor y is full while you wish to set it up for a specific device or learn an extra key function to it. The remote control will then be reset to the default factor y settings and all user settings will be deleted. 1 Keep digit keys 1 and 6 pressed simultaneously for three seconds. – ‘ ’ lights up. The remote control is now in setup mode. 2 Press digit keys 9, 8 and 1, in that order. – ‘981 - WAIT’ appears on the display. All original functions have now been restored and any extra functions have been deleted. 10 Instructions for use 5. Replacing the batteries When the batter y status indicator ( ) on the display star ts blinking, batter y power is low and you should replace the batteries. All user settings will be retained when the old batteries are removed. 1 Press the cover inward, slide it in the direction of the arrow and remove the cover. 2 Inser t 3 AAA/R03 batteries noting the + and configuration inside the batter y compar tment. Place the cover back and click it firmly into place. 6. Support Troubleshooting • Problem – Possible cause / solution • The device you want to operate does not respond at all when a key is pressed. – Point the remote control at the device and make sure that there are no obstructions between the remote control and the device. – Make sure the function you wish to operate is available on the device. – Check if the batter y status indicator ( ) on the display blinks (low batter y power). If this is the case, insert new batteries. • The device you want to operate does not respond properly when a key is pressed. – Maybe the wrong code is programmed for the device during setup. Tr y setting up the remote again. If the device still does not respond, call our helpline. – Check if the batter y status indicator ( ) on the display blinks (low batter y power). If this is the case, insert new batteries. • The teletext keys do not work. – Find out whether your TV is equipped with teletext. • You have difficulties operating all of the functions on your device. – Maybe the remote control has to be adapted to the model of the device. Call our helpline for details. • ERROR appears on the display while adding an extra (advanced) function or when trying to learn a key. – No signal from the original remote control is received for 20 seconds and the SRU 5170 stopped the adding / learning process. Start again from step 1. – An SRU 5170 key is pressed before a signal is detected and the SRU 5170 stopped the adding/learning process. Start again from step 1. – The function you tr y to add is not available on the original remote control. – Make sure the original remote control is working properly. – Make sure the remote controls are properly aligned. – The IR signal of your original device is out of range. The SRU 5170 can only learn IR signals with a carrier signal of 30-60kHz. English 11 Instructions for use English • MEM FULL appears on the display while adding an extra (advanced) function or when trying to learn a key. – No more functions can be added for the selected device or the SRU 5170 memor y is full. Restore all the original functions of your remote control in order to create memor y space. For this, see ‘Restoring the original functions of your remote control’ under 4. ‘Extra possibilities’. All user settings will then be deleted. • The remote control does ...