Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
If this device is installed in a manner such that the radio module FCC ID. label is not visible on the outside of the end product, a label must be placed on the end product with the following statement: "Contains FCC ID. CWU-NXR-MO" This device complies with Part 15 of the FCC rules. Subject to the following two conditions: 1. This device must not cause harmful interference and 2. This device must accept all interference, including interference that interferes with the operation of this device. " The User manual for the end-device must contain the following statements in a prominent place in the manual. Modifications not expressly approved by the manufacturer will void the user’s authority to operate the equipment. This device has been evaluated and found to be compliant with the FCC Rules for RF Exposure when the device is operated at a minimum separation distance of 2 cm. from the user and nearby persons. Operation of this device at closer distances should be avoided. Mio Modero R-3 Remote Overview Mio Modero R-3 Remote Mio Modero R-3 Setup Mio Modero R-3 Setup Inserting or Replacing the Lithium-ion Battery for the Mio R-3 The Mio Modero R-3 comes with a rechargeable Lithium-Ion battery that needs to be installed before use. To install your Lithium-Ion battery into the device: 1. Flip and turn the Mio R-3 device so that the buttons are facing away from you and the device is upside down. 2. Holding the device in both hands, place your thumbs on the battery door and slide the battery door free. The battery door should slide toward the bottom end of the device. 3. Connect the terminal end of the Lithium-Ion battery to the port as shown in FIG. 2. It may be necessary to use a thin, blunt, non-conductive object to seat the battery connector fully within its port. Lithium-Ion Battery Rechargeable Correct path for battery Battery wires and connector Port Connection Rear view - Battery Compartment FIG. 2 Rechargeable Battery Port on The Mio Remote Make sure to inset the battery wires in the case as shown in FIG. 2, or the wires may be damaged when replacing the battery door. 4. Place the battery door back on the device, and slide the door upwards to lock it in place. Battery Low Indicator When the battery charge level is too low to sustain continuous operation, the LCD flashes "Battery Low". If not recharged, the LCD will flash again, and then the device shuts down to prevent a total discharge of the battery. To recharge the battery, insert the Mio R-3 into the Mio Remote Charging Base (see the Mio Remote Charging Base section on page 27). Mio Modero R-3 Remote Mio Modero R-3 Setup Installing Custom Buttons 1. Flip and turn the Mio R-3 device so that the buttons are facing away from you and the device is upside down. 2. Holding the Mio R-3 in both hands, place your thumbs on the battery door and push up to slide the battery door free. The battery door will slide in the direction of the bottom end of the device. 3. Unscrew the 6 screw points indicated in FIG. 3. 6 Screw Points Programming Jack FIG. 3 Internal Mio R-3 Components 4. Turn the unit over so that the buttons are facing you. 5. Lift the top assembly away from the PCB. 6. If necessary, push out the standard buttons from the front of the top assembly. 7. Drop on your custom button pad and verify the alignment with the guide posts on the PCB. 8. Place the top assembly back down on the PCB and return the unit over, exposing the 6 screw points. 9. Tighten the 6 screw points. 10. Replace the battery door, and slide the door upwards to lock it in place. Mio Modero R-3 Remote Setup Mode Setup Mode The Setup mode allows you to set the following device features on the Mio R-3: .. Transmit Mode .. Timeout Adjustment .. Download Mode .. Debug Mode .. Firmware Version .. Device ID .. LED Awake Brightness .. LED Sleep Brightness .. ZigBee ID PAN, Channel, and System Connection .. Site Survey To enter Setup mode: 1. Press and hold the STOP button and the INPUT button. The two buttons must be pressed within 0.1 seconds of each other and held down for 2 seconds. The device indicates you are now in Setup mode. The available modes are listed below. 2. Press the EXIT key when you are finished. The Mio R-3 will automatically exit Setup mode after 30 seconds unless the device is in Download mode. Your settings will not be lost in the event of battery removal or failure. Transmit Mode Press button 1 to select from one of the different available transmission modes. The Transmit mode changes each time 1 is pressed. The predetermined modes are: .. IR 38 Khz .. IR 455 Khz .. ZigBee Mode .. IR 38 + ZigBee .. IR 455 + ZigBee The display indicates the selected mode. 30 seconds after selecting the mode, the menu returns to Setup mode. Timeout Adjustment Press button 2 on the remote to change the sleep timeout from the default. Each time 2 is pressed, the sleep timeout raises incrementally. The predetermined sleep timeouts are 3,6,9, and 12 seconds. The display indicates the selected s...