Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
9 WASH AND DRY Step on Nozzle Setting pedal if necessary to switch from HARD FLOOR DRY VAC to WET SCRUB & VAC position. Slide Brush On/Off switch to the ON position. Pull Solution Trigger to start the flow of cleaning solution. NOTE; Cleaner will continuously dispense solution until Solution Trigger is released. RNING To r, uce _1: the risk of unplug Injury before from IMPOI hard 4T: When changing between nd carpet cleaning modes, use the correct nozzle: ;leaning -tangerine nozzle ning -green bee) nozzle Turn Nozzle Lock Tab counterclockwise to unlock nozzle from cleaner. With solution On/Off trigger held down, slowly push unit forward. Release solution On/Off trigger and pull unit backward in the same area cleaned to remove dirty water and solution from hard floor. Overlap strokes by one inch to prevent streaking. (For heavily soiled areas, repeat if necessary). IMPORTANT: If the unit stops picking up dirty ater and/or the motor changes to a hi, dirty water tank is full be emptied. See page 13. Pull nozzle forward to remove completely from Nozzle Lock. Store nozzle in Nozzle Storage Holster and clip, NOZZLE LOCK TAB 10 Turn Nozzle Lock Tab clockwise to lock nozzle onto cleaner. NOZZLE LOCK TAB insert new nozzle by pushing securely into Nozzle Lock. NOTE: Make sure nozzle is inserted all the way in the Nozzle Lock, otherwise Nozzle Lock will not secure properly. Failure to install nozzle correctly can impact cleaning performance. L_ IMPORTANT: For best cleaning results use a steady, forward and backward motion. Wet cleaning should be done at half the speed of dry vacuuming. For heavily soiled areas, repeat if necessary. BEFORE CLEANING: • Vacuum carpet thoroughly with a regular vacuum cleaner. Remove as much furniture from the room as possible. If unable to remove the furniture, place plastic or foil under and around the legs until the carpet has dried completely. Check for color fastness. Dampen a white cloth with solution. Test a small area in an inconspicuous place. Gently rub the cloth over the area. Check each color for bleeding. If the cloth remains clean, it should be safe to shampoo the carpet. IMPORTANT: Make sure to use the green carpet nozzle and Kenmore ® Carpet & Upholstery Concentrate Cleaner when operating as a carpet shampooer. See page 10 for instructions on changing nozzles. CAUTION: Do not use the cleaner to dry vacuum carpets; this could damage appliance. FILL F- Remove Tank-in- Tank" System from cleaner by pushing down on tank latch and tilting out. Remove measure cap from the rear of the Clean Water Tank. Pour 2capfuls of Kenmore ® Carpet & Upholstery Concentrate Cleaner into Clean Water Tank. 11 Fill remainder of Clean Water Tank with warm water up to the MAX FILL line. Replace \ measure cap on Clean Water Tank. Replace Tank-in-Tank" System by inserting _ ottom first and tiltingforward until tank latch fastens. WASH AND DRY With dry hands, plug cord Into properly grounded electrical outlet. Step on Nozzle Setting pedal if necessary to switch from HARD FLOOR DRY VAO to WET SCRUB & VAC. Turn cleaner on by moving power on/off switch from OFF to ON. Step on Handle Release pedal to put into cleaning position. Slide Brush On/Off switch to the ON position. Pull Solution Trigger to start the flow of cleaning solution. NOTE: Cleaner will continuously dispense solution until Solution Trigger is released. With Solution On/Off trigger held down, slowly push unit forward. Release Solution On/Off trigger and pull unit backward in same area to remove dirty water and solution from carpet. (For heavily soiled areas, repeat if necessary). To aid in the drying On/Off switch to OFF position and continue process, slide Brush operating in WET SCRUB & VAC mode, IMPORTANT: If the unit stops picking up dirty water and/or the motor changes to a high pitch, the dirty water tank is full and must be emptied. See page 13. 12 BRUSHROLL RESET BUTTON IMPORTANT: Your cleaner contains a reset button to protect the permanent belt should the brushroll clog. If this occurs, unplug the unit, remove debris from brushroll, and push reset button prior to resuming operation. THERMAL PROTECTOR IMPORTANT: Your cleaner contains a thermal protective device to shut off the motor to avoid overheating. If this happens, turn the unit off and unplug the cleaner. Inspect the nozzle inlet for blockage. Empty the Dirty Water Tank and clean filter. After approximately 30 minutes, the motor will have cooled and the vacuum will be ready to use. NOTE: The cleaner must remain unplugged during the 30 minute cooling period. WARNING To reduce the risk of Injury from moving parts unplug before servicing• Tank-in-Tank" System: The cleaner is designed with a unique Tank-in-Tank" system. The Clean Water Tank (outer tank) contains the cleaning solution and clean water mixture while the Dirty Water Tank (inner tank) collects wet and dry debris. EMPTY TANK-IN-TANK TM SYSTEM disconnect from electrical outlet. Turn cleaner off and AFTER CLEANING: Allow ca...
Este manual também é adequado para os modelos :Aspiradores - 114.85925 (677.73 kb)