Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
The Recovery Tank is full and the Float Valve in the Recovery Tank has been activated. The Recovery Tank should be emptied. or - 2. The Recovery Tank has foam in the Tank and the Float Valve has been activated. NOTE: If cleaner is accidently turned over while in operation, the float may activate and shut off the suction. If this occurs, set the cleaner upright. Turn Power Switch "OFF" and let motor come to a complete stop. Then tuna switch back on and continue cleaning. VACUUM HOSE TO EMPTY RECOVERY TANK SOLUTION QUICK TUBING See Figure 10 DISCONNECT DET_ VALVE 1. Turn Power Switch "OFF" and Disconnect Power Cord from Electrical Outlet. POWER HEAD HANDLE RECOVERY 2. Disconnect Short Cord located between Solution Tank and Recovery Tank. ALIGN TANK 3. Disconnect Vacuum Hose by depressing the Lock Button "VACUUM" \\ and remove, OVER 4. Twist Solution Tube Quick DisconnectNut counterclock-HOSE wise; lift and remove from Quick Disconnect Valve (See INLET DETAIL "A" ), 5. Lift Latches on Power Head. 6. Lift power Head, by Handle, and remove from Recovery SHORT Tank, 7, Rotate Metal Latch on the Solution Tank and lift Recovery Tank from the Solution Tank, 8, Empty Recovery Tank. 9, Reassemble cleaner and resume cleaning. NOTE: Power Head is designed to go on in only one ix}sition. Make sure LATCF the word "VACUUM" on the Power Head is lined up directly over the Hose Inlet on Recovery Tank as shown in SOLUTION Fig, 10 or Power Head will not seal to unit properly, TANK TO EMPTYTHESOLUTION TANK METHOD ! See Figure 11 When cleaning is completed, both the Recovery Ta nk and the Solution Tank should be emptied prior to storage. Empty the Recovery Tank as described earlier. There are three methods of emptying the Solution Tank. Method 1: 1, Disconnect Short Cord from Recovery Tank. 2. Remove Recovery Tank from Solution 'rank solution out of the Filler Opening. Method 2: and pour 1. Place Floor Nozzle in bath tub or container, 2. Depress Method 3: Solution Release Trigger and spray until empty. 1, Remove Floor Nozzle and insert Wand into Solution Tank through the Filler 2. Vacuum solution out. Opening. 3. All solution is now in Recovery Tank as described earlier. Tank. Empty Recovery METHOD 2 METHOD 3 i UPHOLSTERYNOZZLE See Figure I2 Cleanmore Carpet Cleaner Upholstery Nozzle is an attach ment for furniture upholstery cleaning. The upholstery nozzle may also be used to clean auto upholstery or carpeting. In addition, the nozzle may be used to clean carpeted stairs and other areas difficult to clean with the normal floor nozzle, FLOORTOOLS See Figure 13 The Bare Floor/Carpet Brush (1) may be used on floors without carpet for DRY cleaning with paper dust bag installed. The Squeegee Attachment (2) is useful for WET pickup. CA UTION: DO NOT run the Pump Motor when using these attachments. To prevent Pump Motor from operating, make sure Pump Motor Switch is in "OFF" position, or unplug the Short Cord from the Solution Tank to the Recovery Tank, ®® PAPERDUST BAG (20-5086) See Figure 15 This cleaner uses a disposable paper dust bag to trap and collectdirt when used for dry pick up. It is very important that the disposable paper dust bag remain clean to allow air to pass through it while trapping dirt, If the dust bag is over filled or its pores become clogged from fine powders, no air can pass through, This greatly reduces the efficiency of your cleaner and could cause the dust bag to burst. To maintain your cleaner's peak efficiency, check the disposable paper dust bag often and replace when clogged or approximately one half full. TO INSTALL PAPER DUST BAG 1. Turn Power Switch OFF and disconnect Power Cord from electricM outlet. 2. Lift Latches and remove Power Head from unit, 3. Grasp Cardboard Collar of Dust Bag and push Collar as far as possible onto Bag Adapter Tube. NOTE: For greater ease in assembly, slide bottom of Cardboard Collar onto Adapter Tube first_ then pull top of Collar over Tube, 4, Position Dust Bag around sides of tank to allow motor assembly to fit back in unit. 5. Bend top flap of Cardboard Collar inward, 6, Replace Power Head on unit being carefifl not to crush Dust Bag or to deform flexible splash plate on Power Head. 7, Make sure the Pump Switch is turned "OFF" for Dry Vacuuming. CAUTION: PAPER DUST BAG IS FOR DRY PICK UP ONLY. DO NOT USE WHEN VACUUMING LIQUIDSI COLLAR k DUST BAG BAG ADAPTER TUBE USEAS A BLOWER See Figure 16 1. Insert Hose 2, Turn Power blown. into the Switch Exhaust Port of the Power "ON" and direct hose to Head. area to be EXHAUST PORT KENMORE SPRAYMATE ATTACHMENT MODEL NO. 2°83252 See Figure 17 Cleanmore Spraymate is an optional attachment for carpet cleaning. The Cleanmore Spraymate has a motorized beater brush which is especially good for difficult to clean areas of heavy traffic, Optional cleaning accessories may be purchased or ordered through ycn_rnearest Sears store, A complete set of h_structions comes with each attachment set. PROBLEM POSSIBLESOLUTIONS * !, Neither vacuum mot...
Este manual também é adequado para os modelos :Aspiradores - 175 (1.29 mb)