Assessments - 2, GPA: 3.5 ( )

Fabricante : Clarke Arquivo Tamanho: 1.49 mb Arquivo Nome : Língua de Ensino:

If the red light (8) stays on continuously, there may be debris wrapped around the brush, during operation. At a double motor units this can cause the overload protector for the brush motor to trip. If this occurs, turn the Main Switch (17) OFF and unplug the power cord. Remove any debris from the brush and plug in the power cord, turn the Main Switch (17) back ON. This will automatically reset the overload protector. If the overload protector trips repeatedly contact your dealer for service. For more information of the light indicators at the Dual-versions - see the table below. NOTE! Always disconnect the power cord before performing any machine maintenance. Change the bag whenever the “Bag Full” Light (15) comes on. For details of dust bag replacement see separate instruction in this manual. If the light comes on before the bag is full, the inside of the bag may be coated with very fine dust (change the bag), or debris may be built up somewhere between the brush and the bag. LIGHT INDICATION AND FUNCTION FOR THE BRUSH MOTOR - 212, 215, 218 - Double Motor Units only! LowerLower HigherHigher 5 6 GREEN RED CONDITION FUNCTION 1. ON OFF Normal operation In normal operation, the green light is constantly illuminated. 2. ON - BLINKING OFF Brush position too high (low loading) 1. Green light will blink if the brush is not in contact with the carpet. 2. Green light will be constantly illuminated once the brush is in contact with the carpet or the user adjusts the brush height adjustment to a lower position. 3. OFF ON - BLINKING Brush position too low (heavy loading) 1. If the condition 3, red light blinking, continues for 10 seconds or more, the control module will cut out the power supply to the brush motor. 2. The red light will still be illuminated until you turn off the switch or unplug the cord. 4. OFF ON Brush stalled 1. The red light will be constantly illuminated and the control module will instantly cut the power supply to the brush motor, if the brush was stalled accidentally. 2. The red light will still be illuminated until you turn off the switch or unplug the cord. USING THE WAND (OPTIONAL) The Wand (13) is not supplied as a standard item in all variants of these machines. Do like this in order to use the wand. 1. Push the machine to upright locked position. The brush motor will then stop (Dual-version only), and the brush will be lifted up from the surface at other versions. Then slide the Wand out of its holder. 2. Use the wand for cleaning hard to reach places like floor corners, or furnitures. IMPORTANT ! Foot pedal must be used to release base to operating/non operation position. Failure to do so could result in damage to the handle release mechanism. IMPORTANT ! Foot pedal must be used to release base to operating/non operation position. Failure to do so could result in damage to the handle release mechanism. 12 12 USING THE TOOLS (OPTIONAL) These tools are not standard items in all machine variants. Use these tools for a better cleaning performance at hard to reach areas. A Crevice Tool (14) and Dusting Brush (21) is placed comfortable at the machine, just behind the wand. Remove the wand from the vacuum cleaner and you will have free access to the Tools. 1. The dusting brush is placed in the upper section of the cleaner. 2. The crevice tool is placed in the lower section of the cleaner. 3. Install the Crevice Tool or Dusting Brush on the end of the Wand, if desired. Now the vacuum cleaner will have an extended coverage performance and can be used for cleaning hard to reach areas like roof strips, or furnitures. IMPORTANT ! Foot pedal must be used to release base to operating/non operation position. Failure to do so could result in damage to the handle release mechanism. 33 MAINTENANCE NOTE! Photos belows shows changing of the paper dust bag! Never operate the machine without a Dust Bag in place. 4. 1. 2. 3. Insert a new paper dust bag into the slot of the bag holder and push the bag in place. Check so that the paper dust bag not is jammed in the holder.Only the cardboard piece of the bag should be attached to the bag holder. CHANGING THE PAPER DUST BAG Change the bag whenever the “Bag Full” (15) indicator comes on. To replace the Paper Dust Bag: Disconnect the power cord from the electrical outlet. Pull the Dust lid button (16) and remove the Dust lid outwards to remove it from the cleaner. Push downwards at the edge to the left of the plastic holder, so that the bag inlet loosens from the vacuum inlet of the machine. Grasp at the cardboard piece of the bag and gently pull the full bag outwards -away from cleaner. Always disconnect the power cord beforeperforming any machine maintenance. 5. 6. 1. 2. Push the bag holder with the new bag upwards, so that the bag inlet fasten to the inlet of the machine. Make sure that the bag is unfold and will fit in place at the bag housing. Also check that the ”no bag” clip is placed to the left so that the lid will be able to close. Fit the two notches of t...

Baixe o seu

Para fazer o download, introduza 2 dígitos :