Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
2. Continue to clean soiled area, working in small sections, until no more dirt can be removed. Do not overwet. 3. If the machine loses suction and/or motor noise rises in pitch, turn Power Switch to OFF. Check the Dirty Water Tank Assembly and empty the tank if it is full [see WHEN YOU’RE DONE, page 7]. 4. If spray tip stops spraying, turn Power Switch to OFF and check water and cleaning solution levels. Refill if needed. Never run POWERSTEAMERTM dry. Cleaning Safety Instructions, page 2. If cleaner starts when first plugged in, switch off until ready for use. which contain lemon or pine oil may damage this appliance and void w a r r a n t y. Chemical spot cleaners or solvent- based soil removers should not be used. These products may react with the plastic materials used in your P O W E R S T E A M E R,™ c a u s i n g cracking or pitting. How to clean bare floors How to clean bare floors Snap Together 3. Bottom Front Edge of Lower Chassis Bare Floor Cleaning Tool WARNING: U s e only BISSELL Fiber Cleansing Formula™ i n your POWERSTEAMER.™ Use of cleaning formulas which contain lemon or pine oil may damage this appliance and void w a r r a n t y. Chemical spot cleaners or solvent- based soil removers should not be used. These products may react with the plastic materials used in your P O W E R S T E A M E R,™ c a u s i n g cracking or pitting. Getting ready NOTE: Your POWERSTEAMERTM is not recommended for cleaning wood floors. ¦ Use only BISSELLFloor Cleansing FormulaTM on no-wax floors. Never use BISSELL Fiber Cleansing FormulaTM or other carpet cleaners on bare floors. ¦ Sweep before starting. ¦ Remove old wax before cleaning. ¦ Leave an exit path. ¦ Allow at least 1/2 hour drying time. 1. Remove Clean Water Tank Assembly and Dirty Water Tank Assembly. 2. Tip POWERSTEAMERTM back for easier access to Nozzle. 3. Attach Bare Floor Cleaning Tool to Nozzle with strip facing forward, as shown. Align front edges and snap together. 4. Tip Handle Assembly back by pressing Release Pedal on left side of Lower Chassis and pulling back on Handle Assembly. 5. Take Clean Water Tank to sink area, remove Clean Water Tank Cap and fill Tank with hot (NOT boiling) tap water to fill line. Replace Cap securely. 6. Remove SmartMixTM Formula Tank Assembly from Clean Water Tank Assembly by grasping bottom with fingers and sliding it out. 7. Unscrew SmartMixTM Formula Tank Cap and Insert Assembly and add BISSELL Floor Cleansing FormulaTM to fill line. Reclose Cap tightly. 8. Slide SmartMixTM bottle back into position in Clean Water Tank Assembly. 9. Replace Clean Water Tank Assembly. Slide Tank down front of Handle Assembly until it fits snugly against top of Lower Chassis. Secure with Clean Water Tank Latch Assembly. 10. Replace Dirty Water Tank Assembly. 11. Select SmartCleanTM setting. ¦ WATER ONLY - Use for gentle cleaning, or for (optional) rinsing following cleaning. ¦ NORMAL - Water and Floor Cleansing FormulaTM are mixed to optimize normal cleaning. Use for everyday dirt and soil conditions. ¦ HIGH TRAFFIC - Water and Floor Cleansing FormulaTM are mixed to optimize heavy cleaning. Use for entryways, hallways, heavy soil and stains. This setting may require more frequent refilling on the SmartMixTM bottle. 13. Unwrap Power Cord from Cord Retainer and plug into 120 Volt, 60 Hz grounded outlet as described in Important Safety Instructions, page 2. Cleaning 1. Slowly move the Bare Floor Cleaning Tool back and forth over soiled surface one time while depressing Trigger. Do not overwet. 2. Repeat motion over same area without depressing Trigger. 3. Repeat Steps 1 and 2 until no more dirt can be removed. 4. If machine loses suction and/or noise rises in pitch, turn Power Switch to OFF. Check the Dirty Water Tank Assembly and empty the tank if it is full (see WHEN YOU’RE DONE, page 7). 5. If spray tip stops spraying, turn Power Switch to OFF and check water and cleaning solution levels. Refill if needed. Never run POWERSTEAMER™ dry. WARNING: T h e Dirty Water Ta n k Assembly holds approximately one gallon of soiled liquid. A special float device in the tank will cause the cleaner to stop removing solution from carpet, and the motor sound to rise in pitch when the Dirty Wa t e r Tank Assembly is full. Failure to empty full tank will damage unit. WARNING: Do n o t lay unit on its back with Clean Water Tank Assembly in place. Do not tip up foot with Dirty Wa t e r Tank Assembly in place. Putting it away 1. Follow instructions in WHEN YOU’RE DONE, page 7. 2. Disconnect Solution Tube Connector by turning it counterclockwise and gently pulling it straight from port. 3. Remove Flex Hose Assembly from Dirty Water Tank Triangle port. 4. Replace Dirty Water Tank Triangle Lid. 5. Coil Flex Hose Assembly in Hose Rack on back of POWERSTEAMER.TM 6. Rinse Tools in clean running water, dry, and replace as shown in HOW TO PUT IT TOGETHER, page 4. 7. Wrap Power Cord around Cord Holder on back of POWERSTEAMER.TM 8. Wipe all surfaces with a soft clo...
Este manual também é adequado para os modelos :Aspiradores - 1690 (262.52 kb)