Assessments - , GPA: ( )

Instruções de Operação Bissell, Modelo 1719

Fabricante : Bissell
Arquivo Tamanho: 1.96 mb
Arquivo Nome :

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

NOTE: When charging, the Spot Lifter and charger may become warm to the touch. This is normal and no cause for concern. 2. Spot Lifter must be in “ O ” (OFF) position to charge. 3. When completely charged, your Spot Lifter will operate for up to 7 minutes for model 1718 and up to 15 minutes for model 1719. When completely discharged, it will take approximately 12 hours to fully recharge. Tip: For maximum battery life, completely discharge and recharge Spot Lifter every 1-2 months. Tip: After unit is charged (approximately 12 hours) unplug from outlet. This will aid in prolonging the life of the battery. 4. To charge your Spot Lifter, connect the round end of the charger cord into the power port on the back of the unit. NOTE: Decreased operating time may indicate that the battery has built up a charging resistance. To recharge, first completely exhaust the battery, recharge it, then exhaust it once again before recharging a second time. This procedure may be required more than once. Filling the solution tank 1. Remove solution tank by grasping it firmly and pulling straight up. 2. Unscrew and remove the cap. Add water and formula* to the indicated fill lines on the solution Water Fill Line tank *Note: Your Spot Lifter includes a trial Formula Fill Line size bottle of formula. 3. Replace cap and place solution tank back on unit. 1. WATERFORMULA2. 3. 6 800.237.7691 ug603-5410_1719_806.indd 6 9/25/06 1:07:38 PM 2. Pre-treating1.2. Operations (continued) Turn power switch “I” (ON). To pre-treat stained or highly soiled areas, hold Spot Lifter above soiled surface and press trigger to spray cleaning solution. 3. Let cleaning solution set for 3-5 minutes before cleaning. Tip: Spot cleaning carpet Immediate attention to a spill on 1. Turn power switch “I” (ON). upholstery can prevent permanent 2. Hold Spot Lifter above soiled surface and press staining. trigger to spray cleaning solution, as in pre-treating step 2 above. 3. 3. Press front of Spot Lifter firmly against surface and pull toward you to remove cleaning solution and soil. 4. Repeat steps 2 and 3 until no more dirt or cleaning solution can be removed. Do not overwet. 5. For stubborn soil, use brush to gently scrub soiled area while continuing to spray cleaning solution. To remove brush from unit, gently pull on brush tab and lift out. Tip: NOTE: If Spot Lifter stops spraying, turn “ O ” (OFF) power switch and check Use the brush after applying cleaning solution level. Refill if needed. cleaning solution and remove any Never run dry. surface soil. Using the brush before applying solution can push soil more deeply into carpet. Spot cleaning upholstery 1. Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your Spot Lifter. If tag is coded with an “S” (with diagonal strike-through), or says “Dry Clean Only,” do not proceed. 2. If manufacturer’s tag is missing or not coded, check with your furniture dealer. NOTE: If possible, check upholstery stuffing. Colored stuffing may bleed through fabric when wet. 5. Adsdfdd ghg bvhcvbbj jkn hnbj jkvhgcghhjj fhl kllgh Manufacturer’s Tag 800.237.7691 7 ug603-5410_1719_806.indd 7 9/25/06 1:07:39 PM Operations (continued) Cleaning spills from hard surfaces 1. Turn power switch “I” (ON). 2. Press front of Spot Lifter firmly against hard surface to suction up spill. 3. Press trigger to spray cleaning solution. 4. Press front of Spot Lifter firmly against hard surface to suction cleaning solution, as in step 2 above. NOTE: If the Spot Lifter stops spraying, turn unit “O” (OFF) and check the cleaning solution level in the solution tank. Refill if needed. Never run the unit without water or cleaning solution. Maintenance and care Machine care 1. Turn the power switch to the “OFF” position. ( O ) 2. Carry the Spot Lifter to the sink or drain. To empty the collection tank 1. Remove the collection tank by pressing the tank release button at the top of the tank. The tank will pivot out on a “hinge” at the bottom of the unit. 2. Remove the tank plug by turning approximately 1/4 turn counterclockwise and lifting out. Empty tank. 3. Thoroughly rinse the collection tank with clean water. Be sure to rinse nozzle area. 4. Replace tank plug and turn approximately 1/4 turn clockwise, until snug. 5. To replace the tank, pivot bottom of tank back into "hinge" and tilt up to handle. Press the tank release button, and snap the tank into place. Test for a secure fit before using. NOTE: Check the solution tank. If a significant amount of BISSELL Little Green formula/water remains, you may leave it in the solution tank for your next cleaning task. 2. 3. 2. 3. Tip: Check spray nozzle for accumulated dirt or debris. If necessary, clean with soft bristle brush. 8 800.237.7691 ug603-5410_1719_806.indd 8 9/25/06 1:07:41 PM Machine storage1. Machine storage1. Maintenance and care (continued) Clean exterior surface of Spot Lifter with a soft cloth dampened with water only. Do...