Log:
Assessments - 4, GPA: 4 ( )

Instruções de Operação Bissell, Modelo ADM8IE - 10080030

Fabricante : Bissell
Arquivo Tamanho: 596.73 kb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



Facilidade de uso


The intermittent setting requires the operator to hold any one of the three trigger switches in the “on” position with the fingers, and is typically used in small areas where short cleaning passes are made. The continuous setting allows the operator to set the switch in the “on” position with one touch, and is typically used in large areas where long cleaning passes are made. Lower machine to floor. Adjust handle to comfortable operating position. Tip machine back by main handle to move to starting point. STEP 5 STEP 6 STEP 7 INT CONT CLEANING PROCEDURE 9 ADMIRAL 86038270 05/22/07 Release intermittent trigger switches or turn off continuous setting on solution switch approximately 1 foot before ending cleaning pass. Push down on handle to raise vacuum shoe and brush before moving to the next cleaning pass. Overlap brush contact area a minimum of 1inch on the right (close cleaning) side of machine. During operation, observe the following: The Admiral is equipped with clear internal covers to facilitate operator viewing of dirty solution and vacuum air flow. During operation, observe the vacuum intake cover. Large amounts of water or foam entering the vacuum system can damage the vacuum motor. If you notice either condition, shut down the machine immediately. Empty recovery tank and/or add defoamer to recovery tank. STEP 2 STEP 3 STEP 4 Start at wall closest to power outlet. Pull straight back without pushing down on handle. STEP 1 SOLUTION INTAKE COVER VACUUM INTAKE COVER 1in. (25mm) OFF 1ft. (30cm) CLEANING PROCEDURE ADMIRAL 86038270 05/22/07 10 To speed drying, use a Windblower™ fan. Empty recovery tank by releasing dump hose. Use a hose with cold water to clean out the recovery tank. Also drain solution tank after each use. STEP 7 STEP 8 After cleaning, turn off all controls, return brush to storage position and carefully unplug machine. STEP 6 STEP 5 Use right side of machine for cleaning against walls. RECOVERY DRAIN SOLUTION DRAIN OFF OFF OFF ACCESSORY TOOL USAGE 11 ADMIRAL 86038270 05/22/07 Turn on vacuum motor switch and set solution switch to intermittent position. Note: Be sure brush switch is in off position and brush is in storage position. Squeeze handle on accessory tool to begin cleaning. STEP 3 STEP 4 STEP 1 STEP 2 Use only one of the following acceptable accessory tools. 86000020 – PRV NO. HT 86000000 – PRV NO. DDH 86041150 – PRV NO. DH 86031540 – PRV NO. 39504 86000610 – PRV NO. 89227 86000600 – PRV NO. 89226 Pull back collar and insert over machine mounted fitting, then release collar to lock into place. Lift door on front of vacuum shoe and insert 1 . inch hose cuff into hole. SOLUTION VACUUM ON OFF INT BRUSH TROUBLESHOOTING CHART ADMIRAL 86038270 05/22/07 12 PROBLEM CAUSE SOLUTION No Power, Nothing Runs 1. Is the cord plugged in. 2. Circuit breaker tripped in building. 3. Faulty switch. 4. Faulty power cord or pigtail. 1. Plug in cord. 2. Reset breaker 3. Call for service. 4. Call for service. Vacuum Motor Will Not Run 1.Vacuu...

Este manual também é adequado para os modelos :
Aspiradores - ADM8IA - 10080010 (596.73 kb)
Aspiradores - ADM8IA - 10080010 (596.73 kb)
Aspiradores - ADM8IB - 10080020 (596.73 kb)
Aspiradores - ADM8IS - 10080040) (596.73 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias