Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
2 To clean carpets, push the rocker switch again (Fig. 15). The brush strip disappears into the nozzle housing and the wheel is lowered automatically. , Combination nozzle (specific types only) The combination nozzle can be used on either carpets or hard floors. 1 To clean hard floors, push the rocker switch on top of the nozzle with your foot (Fig. 16). The brush strip for cleaning hard floors comes out of the nozzle housing. ,2 To clean carpets, push the rocker switch again (Fig. 17). The brush strip disappears into the nozzle housing. , English Hard floor nozzle (specific types only) -The hard-floor nozzle is designed for gentle cleaning of hard floors (Fig. 18). accessories You can connect the crevice tool (1), the small nozzle (2) or the small brush (3) directly tothe handgrip of the hose or to the tube. Use the same method as for the tube. (Fig. 19) -Use the crevice tool to clean narrow corners or hard-to-reach places. -Use the small nozzle to clean small areas, e.g. the seats of chairs and sofas. -Use the small brush nozzle to clean computers, bookshelves etc. accessory holder 1 2 Snap the accessory holder onto the handgrip (Fig. 20). Snap two accessories into the accessory holder: -Crevice tool and small nozzle (Fig. 21). -Crevice tool and small nozzle (Fig. 22). Note:The small nozzle must be placed in the accessory holder as shown in the picture. infrared remote control (specific types only) 1 2 Remove the battery compartment cover. Place the batteries in the battery compartment (Fig. 23). Make sure the -and + poles point in the right direction. 3 Reattach the battery compartment cover using the appliance 1 2 Pull the cord out of the appliance and put the mains plug in the wall socket. Press the on/off button on top of the appliance with your foot to switch on theappliance (Fig. 24). adjusting suction power During vacuuming, you can adjust the suction power. -Use maximum suction power to vacuum ver y dir ty carpets and hard floors. -Use minimum suction power to vacuum cur tains, table carpets, etc. infrared remote control (specific types only) With the infrared remote control, you can set the suction power to one of 5 different suction power settings. -When you switch on the appliance, it always star ts operating at the highest suction power setting. -To reduce the suction power by one setting, press the - button. (Fig. 25) To increase the suction power by one setting, press the + button. suction power knob (specific types only) -During vacuum cleaning, you can adjust the suction power with the suction power knob on top of the appliance (Fig. 26) 10 English Pausing during use 1 2 3 If you want to pause for a moment, insert the ridge on the nozzle into the parking slot to park the tube in a convenient position (Fig. 27). If the appliance is equipped with an infrared remote control (specific types only), press thestandby button to switch off the vacuum cleaner temporarily, for instance when you have tomove some furniture. (Fig. 28) To continue vacuum cleaning, press the standby button again.The appliance then starts operating at the previously selected suction power setting again. storage 1 2 3 4 5 Slide the tube parts into each other to reduce the tube to its shortest length. Switch off the appliance and remove the mains plug from the wall socket. Press the cord rewind button to rewind the mains cord (Fig. 29). To store the appliance in upright position, insert the ridge on the nozzle into the storage slot (Fig. 30). Always put the TriActive nozzle in the carpet setting when you store it (brush strip retracted into the nozzle). Also prevent the side brushes from becoming bent (Fig. 15). replacing/emptying the dustbag Always unplug the appliance before you replace the disposable dustbag or empty the reusabledustbag. Note: In some cases, the dustbag-full indicator can indicate that the dustbag is full, even though it is not. This may occur if the pores of the dustbag are clogged (e.g. when you have vacuumed ashes, fine sand, lime, cement dust and similar substances) or if something is blocking the nozzle, tube and/or hose. If the pores of the dustbag are clogged, you have to replace the dustbag, even if it is not full yet. If the dustbag is not clogged but not full either, something is blocking the nozzle, tube and/or hose. In this case, do not replace the dustbag but remove the obstruction. replacing the disposable dustbag -Replace the dustbag as soon as the dustbag-full indicator has changed colour permanently, i.e. even when the nozzle is not placed on the floor (Fig. 31). 1 Pull the cover upwards to open it (Fig. 32). 2 Lift the dustbag holder out of the appliance (Fig. 33). Make sure you hold the holder with the dustbag in horizontal position when you lift it out of the appliance. Pull at the cardboard tag to remove the full dustbag from the holder (Fig. 34). The dustbag is sealed automatically. Slide the cardboard front of the new dustbag into the two grooves of the dustbag holder asfar as possi...
Este manual também é adequado para os modelos :Aspiradores - FC9174/08 (8.21 mb)