Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Preparing for use 1 Connect the upper stick part to the handgrip (‘click’) (Fig. 2). -Make sure the ridge on the handgrip aligns with the groove on the upper stick par t. 2 Connect both the upper and lower stick parts to the joint (‘click’) (Fig. 3). -If you do not want the stick to be bendable, you can use it without the joint. Simply connect the upper stick par t with handgrip to the lower stick par t directly (‘click’) 3 To bend the stick, press the stick bending button (Fig. 4). -With a bent stick, you can clean areas under furniture without bending your back (Fig. 5). 4 To remove the stick, press the stick release button on the lower handle (1) and pull the stick upwards (2) (Fig. 6). Charging Charge the appliance when the roller brush does not turn as fast as usual. Charge the appliance for 16-18 hours. English 9 For optimal battery performance, do not charge the appliance after every use. Only charge the appliance when the battery pack is low (i.e. when the roller brush does not turn as fast as usual). Switch off the appliance before you charge it. Place the stick in upright position (Fig. 7). Insert the small plug into the socket on the sweeper base (Fig. 8). Insert the adapter into a wall socket. 1 2 3 4 -The charging light is on continuously during charging and after the batter y pack is fully charged.The charging light goes out when you disconnect the appliance from the mains Note:The charging light does not give any information about the charge level of the battery pack. using the appliance 1 To unlock the stick from its upright position, put your foot on top of the sweeper base to prevent it from tilting.Then pull the handle towards you. (Fig. 9) Do not put your foot on the on/off button or the dirt tray release button. 2 Press the on/off button to switch on the appliance (Fig. 10). To switch off the appliance, press the on/off button again. 3 4 Use the side brushes to clean the floor along the walls (Fig. 11). To bend the stick, press the stick bending button (Fig. 4). -With a bent stick, you can clean areas under furniture without bending your back (Fig. 5). 5 To use the sweeper as a handheld appliance, remove the stick and hold the sweeper by the lower handle (Fig. 12). For better grip, push the handle towards the front of the appliance until it is at a 45-degree angle to the base. 10 English Cleaning Never clean the appliance or any of its parts in water or in the dishwasher. 1 2 Disconnect the appliance from the mains before you clean it. Clean the appliance and its parts with a damp cloth. Emptying the dirt tray 1 Always empty the dirt tray after use. 2 Place the stick in upright position (Fig. 7). 3 Press the dirt tray release button (1) and lift the dirt tray out of the sweeper base (2) (Fig. 13). 4 Hold the dirt tray over a dustbin.Then press the slide on the lower handle downwards to open the dirt tray door and empty the dirt tray (Fig. 14). 5 Place the dirt tray back into the sweeper base and push it down into position (Fig. 15). The dir t tray door closes automatically when you put the dir t tray back into the sweeper base (‘click’). Cleaning the roller brush Switch off the appliance before you clean the roller brush. Rotate the roller brush until the cutting groove faces you. Use a pair of scissors to cut the hairs, threads etc. that have collected around the roller brush (Fig. 16). Remove fluff, hairs and other dirt from the roller brush. 1 2 3 Note: If you are unable to clean the roller brush properly in this way, you can remove it for more thorough cleaning. See sections ‘Removing the roller brush’and ‘Reinserting the roller brush’ below. English 11 removing the roller brush 1 2 3 4 To remove the stick, press the stick release button on the lower handle (1) and pull the stick upwards (2) (Fig. 6). Turn the sweeper base upside down, push the retainer release slide in the direction of the arrow (1) and remove the retainer (2) (Fig. 17). Slip the belt off the end of the roller brush (1) and lift the roller brush out of the base (2) (Fig. 18). Remove fluff, hairs and other dirt from the roller brush and the groove. reinserting the roller brush 1 2 Slip the belt over the ribbed end of the roller brush. Insert the other end of the roller brush into the slot opposite the belt (Fig. 19). Insert the end of the roller brush with the belt into the other slot. (Fig. 20) Do not force the roller brush into the slot. Rotate the roller brush so that the ridge on the side with the belt points upwards. 3 Put the retainer back into the slot (1) and slide the release slide toits original position (‘click’) (2) (Fig. 21). If the roller brush is not properly inser ted, you cannot move the release slide to locked position. Cleaning the wheels 1 2 3 Switch off the appliance. Place the sweeper base upside down. Insert a slotted screwdriver underneath one of the wheels. Rotate the screwdriver to loosen the wheel and axle from the groove (Fig. 22). Do not place your hand on the wheel. Repeat step 3 to rem...