Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Do NOTadd cleaning solutions, scented perfumes, oils or any other chemicals to the water used in this appliance as this may damage the unit or make it unsafe for use. OPERATING INSTRUCTIONS Filling or Re-filling Your Steam Cleaner With Water 5 IMPORTANT: Always insure that the unit is “UNPLUGGED” from the wall receptacle prior to initial filling or re-filling the water tank and has been allowed to cool for 15 minutes. Never attempt to fill this unit under awater tap, always use the filling funnelprovided. 8 OPERATING INSTRUCTIONS Before Re-Filling: Step 1: Press the steam switch on the hand grip to the “On” position to vent any remaining steam that is in the boiler. Fig. 1ComponentsOn/Off Switch: The unit is “On” when the switch is in the “Pushed down” position. The light on the On/Off switch will illuminate when the unit is on. The unit is “Off” when the switch is in its “Up” position. Heating Light (red): This light will illuminate when the unit is heating up the water. Steam Ready Light (green): When this light is “On”, it indicates that the steam is ready to use.CAUTION: Read the instructions for “Filling or Re-Filling Your Steam Cleaner with Water” before opening the Safety Cap. CAUTION: Always unplug before filling. ALLOW UNIT TO COOL FOR FIFTEEN (15) MINUTES BEFORE REFILLING.IMPORTANT: Do NOTadd cleaning solutions, scented perfumes, oils or any other chemicals to the boiler in this appliance. Use tap water or distilled/ purified water if the tap water in your area is very hard. Fig. 2Assembly of CastersThe casters for your new steam cleaner are packed and shipped unassembled. To assemble the casters to the base of the steam cleaner, simply insert the caster stems onto one of the four (4) posts on the base and push downward with the palm of your hand. Repeat for the next three (3) casters. Step 2: Press the steam switch to the “Off” position, turn the unit off, unplug the unit from the electrical outlet and let the unit cool for 15 minutes. Step 3: Plug the power cord into an electrical outlet, assure that the On/Off switch is in the Off position and press the steam switch on the hand grip to the “ON” position tovent any residual steam that is in the boiler. (Fig 1) Step 4: Remove the power cord from the electrical outlet and turn the steam switch on the hand grip to the “OFF” position. (Fig. 1) Step 5: Place the unit on a flat, stable surface. Slowly turn the safety filler cap counter clockwise until it is removed. Step 6: Insert the funnel into the tank opening and add 84 US Fl Oz (2.4L) of water. (Fig. 2) Place the funnel in the tank opening as illustrated inFig. 2. The funnel has beenspecially designed to show when the water tank is full. When water starts to come out of the vent hole of the funnel, the tank is full. Remove the funnel slowly and let the remaining water in it go inside the water tank. Do Not Overfill. Step 7: Replace the Safety Filler Cap. WARNING: Allow unit to cool for 15minutes before refilling. When refilling the steam cleaner while the boiler is still hot, there is a risk that water will squirt back during filling and cause scalding. Extreme care should be taken when refilling the unit. Use caution when opening the Safety/Filler Cap as cap may become hot during use and escaping steam can cause scalding. Text Box: Efficient Work For vertical surfaces, wipe with a towel from the top down, in this way the dirty water will no Efficient Work• For vertical surfaces, wipe with a towel from the top down, in this way the dirty water will not soil surfaces already cleaned. • Avoid changing brushes back and forth while cleaning. • Start with the smallest brush to clean tight spots and corners first. • Use a towel to wipe dirt as soon as possible, otherwise it will dry and re-adhere to the surface. If you consistently use demineralized or distilled water, cleaning the tank is unnecessary. Rinsing Out the Steam CleanerNormally, a periodic rinse of your steam cleaner will free it from deposits. This is recommended every 10-15 tankfulls, to free up any scale deposits from the tank. Fill the boiler with 20 oz. of water and shake the cleaner vigorously. Tilt the cleaner upside down to empty the boiler of water and any scale deposits. Descaling Your Steam CleanerIf the tap water in you area contains a high level of calcium depositsand you have been using tap water to do your steam cleaning, you should descale your unit after 10-15 tankfulls. Step 1: Unplug the steam cleaner from the power source before you descale the boiler. Allow to cool. Step 2: Fill the boiler with 1 part vinegar and 5 parts water and leave overnight or for a period of approximately 8 hours. Do not screw the safety/filler cap onto the steam cleaner while you are descaling the boiler. Do not use the steam cleaner while descaling solution is inside the boiler. Step 3: After the period of soaking, turn the steam cleaner upside down to empty solution from the boiler. Due to the fact that a small amount of solution will be left ...