Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
Tips On How To Use Your SystemWater• Use tap water for all your cleaning needs. • However, if you live in an area with hard water, use de-mineralized / distilled water when steaming light colored fabrics to eliminate the possibility of hard water stains. IMPORTANT: Do NOTadd cleaning solutions, scented perfumes, oils or any other chemicals to the water used in this appliance. Use tap water or distilled/ purified water if the tap water in your area is very hard. WARNING: A towel wrapped around the brush can become hot enough to burn. Make sure that you let the towel cool off for 5 minutes before touching it. Using Towels• For best results use 100% cotton white terry cloth towels. • Use correct size of towel to allow you to wrap the towel around the brushes and clip it under the spring loaded cloth holder. • The purpose of using a towel is to absorb moisture and dirt being removed. Always use dry towels. A wet towel will smear the dirt. • Wash towels with strong detergent and bleach. • Using scented fabric softener while washing the towels will cause the scent to be released into the airwhen using the towels with your steam system.Efficient Work• For vertical surfaces, wipe with a towel from the top down, in this way the dirty water will not soil surfaces already cleaned. • Avoid changing brushes back and forth while cleaning. • Start with the smallest brush to clean tight spots and corners first. • Use a towel to wipe dirt as soon as possible, otherwise it will dry and re-adhere to the surface. Step 1: Disconnect electrical power cord from wall outlet. Step 2: Depress and hold the hand grip steam trigger to ensure that any remaining pressure in the boiler has been released. Step 3: Carefully loosen the safety/filler cap by turning counter clockwise. Any residual steam wil be released below the safety/filler cap if the tank has not been completely vented. When the hissing stops and the last of the steam has been released, remove the filler cap. Allow unit to cool down. CAUTION: Allow unit to cool for 15 minutes before refilling. If the steam cleaner is still hot, there is a risk that water will squirt back during filling and cause scalding. Extreme care should be taken when refilling the unit. Use caution when opening the safety/filler cap as cap may become hot during use and escaping steam can cause scalding. Step 4: Allow the steam cleaner to cool for 15 minutes before re-filling with water. Step 5: Refill water tank with water using the filling funnel. Step 6: Firmly screw the safety/filler cap back onto the unit by turning clockwise. Step 7: Connect power cord to the wal outlet. Using Your Steam Cleaner with Floor Brush NOTE: Fit floor brush with the angle adapter on to the extension tube. OPERATING INSTRUCTIONS Refilling Your Steam Cleaner With Water 6 Step 2: If the angle adapter is not attached to the floor brush, hold the brush with its bristles up in your left hand. With the angle adapter pointing downward, insert it into the hole in the back of the brush, then turn the floor brush 180° . Step 3: Insert the electrical power cord into the wal outlet. Heating time is approximately 8-10 minutes with cold water. Filling the steam generator with hot water wil shorten the heat up time. Note: If you require continuous steam, depress the trigger and engage the trigger lock. (Fig. 2) Step 1: Connect one of the extension tubes to the hand grip on the flexible steam hose. To attach the extension tubes one onto the other or onto the hand grip, press the locking button ensuring that it fits into the hole. (Fig. 2, Fig. 3) To disconnect, repeat the operation by pressing the locking button and pulling the two sections apart. Cleaning the Floor Brush 7 1. Prepare white terry cloth towel: size 8” x 17” folded in half or place one on top of another to have two layers. (Fig. 5) 6. Place the towel around the brush, and repeat folding the towel as shown in Fig. 9. When folding the towel, leave some slack. Do notpull tightly around the brush, leave some looseness. Fig. 2Fig. 3 To clean the floor brush after you have finished using: 1. Lift the front clip on the floor brush (Fig. 4) and remove the brush. 2. Rinse the bristle brush and the diffuser housing under warm water. 3. Replace bristle brush onto the diffuser housing. Fig. 4 OPERATING INSTRUCTIONS100% white terry cloth towel can be fitted on this brush, so as to absorb the dirt and protect delicate surfaces. Important: Please note that bristles may break through thin towels. To cut and make your own towels, we recommend that you use one (1) towel 8” x 17” folded in half or two (2) towels 4” x 17” laid one on top of the other be used. This will ensure that the brush bristles do not break through and that the towels will be sufficiently absorbent and retain as much dirt as possible. Very Important: When installing the towels to the floor brush, ensure that the towels do not cover the front and the back of the brush. (See Fig. 9) Attaching a Towel to the Floor Brush4. F...