Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
Using the Manual Trigger Spray, apply a sufficient amount of water and solution to the stain. Wait 3-5 minutes before cleaning. Plug in the unit. While holding the SpotLifter PowerBrush above the area to be cleaned, apply water and formula by depressing the Manual Trigger Spray, dispensing fluid to the soiled/stained area. Turn the power switch to the “ON” position. ( I ) 1. 2. How To Use Your SpotLifter® PowerBrush Filling Your Clean/Solution Tank 3. Pre-Treating 1. 2. Cleaning 1. 2. 3. 1. 2. 2. 3. How To Use Your SpotLifter® PowerBrush Filling Your Clean/Solution Tank 3. Pre-Treating 1. 2. Cleaning 1. 2. 3. 1. 2. 2. 3. Cleaning Continued 4. Powerbrush firmly against the surface area to be cleaned, lifting the brushes up off the surface. Pull toward you to remove the soil and cleaning solution. Note: Step #4 may be repeated until no more dirty water is removed or until the area to be cleaned meets your satisfaction. Check the Dirty/Collection tank and empty the tank if it is full (See Clean Up/Storage, page 8). If the Spotlifter PowerBrush stops spraying, turn off the unit and check the Cleaning Solution level in the Clean/Solution Tank. Refill if needed. Never run dry. Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your SpotLifter PowerBrush. If tag is coded with an “S” (with diagonal strike-through) or states “Dry Clean Only”, do not proceed. If manufacturer’s tag is missing or not coded, check with your furniture dealer. If possible, check upholstery stuffing. Colored stuffing may bleed through fabric when wet. Turn the unit on to activate the suction. Press the front of SpotLifter PowerBrush firmly against surface to vacuum the spill. Press the Manual Trigger Spray to apply the cleaning solution. Press the front of the SpotLifter PowerBrush firmly against the surface to vacuum the cleaning solution. Check the Dirty/Collection tank and empty the tank if it is full (See Clean Up/ Storage, page 8). If the SpotLifter PowerBrush stops spraying, turn off the unit and check the Cleaning Solution level in the Clean/Solution Tank. Refill if needed. Never run dry. 6. 1. 2. 4. 1. 7 Deep Cleaning Upholstery Cleaning Spills From Hard Surfaces 2. 3. 3. Tip: You may also spray water and formula, with the Manual Trigger Spray, while the unit is turned on and you are using the Dual PowerBrushes and Suction to clean. Tip: Fast attention to a spill on upholstery can prevent permanent staining. Tip: When cleaning a vertical surface (ie chair back, auto interior, etc.) begin with a completely empty Dirty/Collection Tank. Brushing and Suction can be done separately, based on how you hold and use the unit. To Use The Dual Powerbrushes Only: Tilt the unit forward slightly, placing both brushes in contact with the carpet. The flat surface of the brush cartridge should be parallel to the surface being cleaned For Suction Only: Tilt the unit forward, pressing the front of the Spotlifter 5. 5. 6. Clean-Up/Storage Clean-Up/Storage 8 Turn the power switch to the “OFF” position. ( O ) Unplug the unit. Carry the SpotLifter PowerBrush to the sink or drain. First you need to remove the Clean/Solution Tank. Gently press the Quick Release tabs on the Clean/Solution Tank and slide the tank off of the unit. Grab the Dirty/Collection Tank and pull to remove. While at the sink, remove the Tank Cap by turning approximately 1/4 turn counterclockwise and lift out the cap. Empty the tank. Rinse the Dirty/Collection tank with warm water. Replace cap and turn approximately 1/4 turn clockwise, until snug. Slide the Dirty/Collection Tank into the unit. Replace the Clean/Solution Tank. Note: If a significant amount of water and formula remains in the Clean/Solution Tank, you may leave it in the Clean/Solution Tank for your next cleaning task. NOTE: Make sure the Power Switch is in the “OFF” position. ( O ) Firmly grasp the Brush Cartridge from the side of the unit and pull out from the unit. To remove any debris that may have collected around the Dual Powerbrushes, rinse the Brush Cartridge under warm water. Replace the Brush Cartridge into the unit by gently guiding the Cartridge in the unit. Once it is in place, firmly “snap” the Brush Cartridge in place. NOTE: Do not attempt to remove or insert the Brush Cartridge while the unit is running. This will damage your unit. To Empty the Dirty/Collection Tank To Clean the Dual Powerbrushes 1. 2. 1. 3. 2. 3. 4. 5. 6. 1. 2. 3. 1. 2. 3. 1. 2. Putting It Away Store in a dry area, at room temperature to avoid freezing. To Replace the PowerBrush Belt If the belt should break, to replace: Tip: If you do not have the Brush Cartridge in all the way, the Dual Powerbrushes will not rotate. Firmly push the cartridge in place, while listening for the “snap” to know it is in all the way 9 Remove the screw in the belt cover using a Phillips Screwdriver. Take the broken belt out. Replace the new belt over the 2 belt gears. Replace the belt cover door. 1. WARNING: To reduce the risk of...