Press [F], [MARK] to turn the internal GPS function ON or OFF. [TNC] (2) Press [TNC] to turn the built-in TNC ON and the APRS (or NAVITRA) mode ON. • Each time you press [TNC], the mode cycles through the following: APRS (or NAVITRA) mode ON . PACKET mode ON . TNC OFF. • When the built-in TNC turns on, “OPENING TNC” appears on the display. • During “OPENING TNC” appears on the display, the mode cannot be changed. Press [F], [TNC] to turn the Tracking Log function ON or OFF. [POS] (3) Press [POS] to display your “My position” (using the internal GPS) or to enter the Position registration mode (not using the internal GPS) . Press [F], [POS] to enter the My Weather mode . [MSG] (4) Press [MSG] to display the Message list. Press [F], [MSG] to enter the New Message input mode . 11 [LIST] (5) Press [LIST] to display the Station list. Press [F], [LIST] to display the DX Cluster list . [BCON] (6) Press [BCON] to enter the Beacon Transmit mode (When TX Beacon method is Manual) or turn the Beacon function ON or OFF (When TX Beacon method is other than Manual) . Press [F], [BCON] to enter the Quick Beacon mode . [REV] (7) Press [REV] to turn the Reverse function ON or OFF. Press [REV] (1s) to turn the Automatic Simplex Checker ON. Press [F], [REV] to enter the Voice Alert function setup mode . [TONE] (8) Press [TONE] to turn the Tone function ON. • Each time you press [TONE], the function cycles through the following: Tone ON . CTCSS ON . DCS ON . Cross Tone ON . OFF. • Additionally, when APRS is ON and Voice Alert is configured, Voice Alert ON is added to the above cycle. Press [F], [TONE] to enter the Tone frequency, CTCSS frequency, DCS code, or Cross Tone setup mode. Press [F], [TONE] (1s) to start the Tone frequency ID, CTCSS frequency ID, or DCS code ID scan. [PF] (9) Press [PF] to activate its programmed function. The default function is “Weather Channel” (TH-D72A)/ “Memory Name < > Frequency” (TH-D72E). [MHz] ( ) Press [MHz] to enter the MHz mode. Press [MHz] (1s) to start the MHz scan. Press [F], [MHz] to enter Offset Direction setup mode. • Each time you press [F], [MHz], the offset direction cycles through the following: plus (+) direction . minus (–) direction . –7.6 MHz (TH-D72E only) . OFF. [DUAL] (0) Press [DUAL] to switch the Single band mode and Dual band mode. Press [F], [DUAL] to turn the Full duplex function ON or OFF. [ENT] (#) Press [ENT] to enter Frequency or Channel number entry mode. Press [F], [ENT] to enter Frequency step setup mode. 12 Indicator Description Appears while using Economic low output power. Appears while using Low output power. Appears while using High output power. Appears when the Beacon type is set to “APRS”. Appears when the Beacon type is set to “NAVITRA”. Appears while using Packet mode. Appears when the packet transfer rate is set to 1200 bps. Appears when the packet transfer rate is set to 9600 bps. Appears when a message is received. Appears while in Stand-by (Packet mode) Appears while Connected (Packet mode) Appears when the Beacon function is ON. Appears when the external GPS is ON. Blinks while positioning. Appears when the internal GPS is ON. Blinks while positioning. Appears while the internal GPS save mode is activated. Appears when the Track Log is ON. Appears when the Weather Instrument is ON. Appears when the internal GPS and Weather Instrument is ON. Performs as an S meter when receiving a signal and displays the selected power level while transmitting. Displa y 13 Indicator Description Appears when the Tone function is ON. Appears when the CTCSS function is ON. Appears when the DCS function is ON. Appears when the Cross tone setting is “TONE/CTCSS”. Appears when the Cross tone setting is “DCS/CTCSS”. Appears when the Cross tone setting is “TONE/DCS”. Appears when the Cross tone setting is “DCS/Off”. Appears when Voice Alert is set to “On”. Appears when Voice Alert is set to “RX Only”. Appears when the Shift function is set to plus. Appears when the Shift function is set to minus. Appears when the Shift function is set to –7.6 MHz. Appears when the Reverse function is ON. Appears when the ASC function is ON. Blinks when the ASC function is performing an OK check. Appears while in Full Duplex mode. Appears while in AM mode. Appears while in Narrow FM mode. Appears when the VOX function is ON. Appears when the Key Lock function is ON. Displays the operating frequency. Appears while using the Internal data band. Appears when the selected channel is not registered while in Memory Input mode. Appears when the selected channel is registered while in Memory Input mode. Displays the Memory channel number. Appears when the Memory Channel Lockout function is ON. Appears when Weather Alert is ON. Blinks when receiving a signal. (TH-D72A only) 14 BASIC OPERATIONS SWITCHING THE POWER ON/ OFF Press the [ ] (1s) to switch the transceiver ON. • The power on message momentarily appears on the display. • If the trans...
