Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Electricidade - SCD510/00 (729.28 kb)
Electricidade - SCD510/00 (1.15 mb)
Electricidade - SCD510/00 (644.91 kb)
Facilidade de uso
3 Reattach the lid. (Fig. 7) Note:When the batteries are low, the battery light on the baby unit flashes red. EngliSh 11 parent unit Battery operation (rechargeable battery pack) The parent unit comes with a SCD510 NiMH rechargeable batter y pack. Charge the parent unit before you use it for the first time or when the batter y light indicates that the batter y pack is low.The batter y light flashes red when the batter y pack is low. The batter y light star ts to flash red 30 minutes before the batter y pack is completely empty. Note: If the battery pack is completely empty, the parent unit automatically switches off and loses contact with the baby unit. 1 Remove the lid of the compartment for the rechargeable battery pack (Fig. 8). 2 Insert the rechargeable battery pack (Fig. 9). Note: Make sure the + and - poles of the battery pack point in the right direction. 3 4 5 , When you charge the parent unit for the first time or after a long period of non-use, switch it Reattach the lid (Fig. 10). Put the small appliance plug in the parent unit and put the adapter in a power outlet (Fig. 11). , Leave the parent unit plugged in until the battery pack is fully charged. During charging, the battery light lights up red continuously. When the battery pack is fully charged, the battery light lights up green continuously. - off and let it charge continuously for at least 10 hours. -Charging normally takes 8 hours, but it takes longer when the parent unit is switched on while charging.To keep the charging time as shor t as possible, switch off the parent unit during charging. -When the batter y pack is fully charged, the parent unit can be used cordlessly for at least 24 hours. Note:When the parent unit is charged for the first time, the operating time is less than 24 hours.The battery pack only reaches its full capacity after you have charged and discharged it four times. Note:When the parent unit is not connected to a power outlet or even when the parent unit is switched off, the battery pack gradually discharges. Using the appliance Use the baby monitor for its intended household use as described in this manual. 1 Place the parent unit and the baby unit in the same room to test the connection (Fig. 12). Make sure the baby unit is at least 3.5 feet/1 meter away from the parent unit. 2 Press and hold the on/off button 3 on the baby unit until the green power-on light goes on. (Fig. 13) Note:The power-on light always lights up green, even when there is no connection with the parent unit. The nightlight lights up briefly and then goes out again. , The battery light Tlights up briefly and then goes out again. ,3 Press and hold the on/off button 3 on the parent unit until the sound level lights light up briefly. (Fig. 14) The battery light briefly lights up red and then lights up continuously (Fig. 15). , The LINK light flashes red. (Fig. 16) , The LINK light on the parent unit turns green and lights up continuously when a connection , has been established between the baby unit and parent unit (Fig. 17). If no connection is established, the LINK light on the parent unit stops flashing and lights up , red.The parent unit beeps from time to time. (Fig. 18) 12 EngliSh positioning the baby monitor 1 2 Place the baby unit at least 3.5 feet/1 meter away from your baby (Fig. 19). Place the parent unit within the operating range of the baby unit. Make sure it is at least 3.5 feet/1 meter away from the baby unit to avoid acoustic feedback (Fig. 20). For more information on the operating range, see section ‘Operating range’ below. Operating range The operating range of the baby monitor is 1000 feet/330 meters in open air. Depending on the surroundings and other disturbing factors, this range may be smaller. Indoors the operating range is up to 150 feet/50 meters. Wood, plaster, cardboard, glass (without metal, wires or lead) < 12in/30cm 0-10% Brick, plywood < 12in/30cm 5-35% Reinforced concrete < 12in/30cm 30-100% Metal grilles or bars < 0.4 in/1cm 90-100% Dry materials Material thickness Loss of range Metal or aluminum sheets < 0.4 in/1cm 100% For wet and moist materials, the range loss may be up to 100%. Features adjusting loudspeaker volume 1 Press the volume + or - button on the baby unit until the desired loudspeaker volume for the baby unit has been reached. (Fig. 21) Note:You only have to adjust the baby unit volume when you use the talk function (see below). 2 Press the volume + or – button on the parent unit until the desired loudspeaker volume for the parent unit has been reached (Fig. 22). Note: If the volume is set to a high level, the units consume more power. Talk function You can use the TALK button on the parent unit to talk to your baby (e.g. to comfor t your baby). 1 2, Press and hold the TALK button and talk clearly into the microphone from a distance of 6-12in/15-30cm (Fig. 23). The green LINK light starts flashing. Release the TALK button when you have finished talking. Sound level lights The parent unit continuo...