Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Display of the parent unit (Fig. 1) 1 Signal strength indicator 2 Eco Max indicator 3 Night dim mode symbol 4 Cr y aler t indicator 5 Mute symbol 6 Batter y status indicator 7 Humidity aler t symbol 8 Navigation arrow 9 Temperature symbol 10 Microphone sensitivity indicator 11 Nightlight symbol 12 Lullaby symbol 13 Projector symbol 14 Timer or timer repeat symbol 15 Soothing menu screen Preparing for use iMPortant: read the safety instructions carefully before you use the baby monitor and keep them for future reference. Baby unit We advise you to use the baby unit from the mains.To guarantee automatic power backup in case of mains failure, you can inser t four 1.5V AA alkaline batteries (not included). Do not use rechargeable batteries.The baby unit does not have a charging function and rechargeable batteries discharge slowly when they are not in use. Parent unit The parent unit runs on two rechargeable batteries that are supplied with the baby monitor. Charge the parent unit before you use it for the first time and when the batteries are low. Please note that you have to charge the parent unit for the full 10 hours to have a cordless operating time of 18 hours. Note:When you start using the baby monitor, it takes four charge and discharge cycles before the rechargeable batteries reach their full capacity. using the baby monitor Positioning the baby monitor Keep the baby unit out of the reach of the baby. Never place the baby unit inside the baby’s bed or playpen. -Because the cord of the baby unit presents a potential strangulation hazard, make sure that the baby unit and its cord are at least 1 metre/3.5 feet away from your baby. -To prevent a high-pitched sound from one or both units, make sure the parent unit is at least 1 metre/3.5 feet away from the baby unit. EngliSh Linking parent unit and baby unit 1 2 Press and hold the 3 button on the baby unit for 2 seconds until the power-on light goes on. Press and hold the 3 button on the parent unit for 2 seconds until the display lights up.The ‘link’ light on the parent unit starts flashing red and the message ‘I AM LINKING’ appears on the display. When the parent unit and baby unit are linked, the ‘link’ light turns solid green.The signal , strength indicator and the message ‘LINKED’ appear on the display. If no connection is established, the message NOT LINKED is displayed and the parent unit , starts to beep. What to do if no link is established -If the parent unit is out of range, place it closer to the baby unit, but not closer than 1 metre/ 3.5 feet. -If the baby or parent unit is too close to another DECT appliance (e.g. a cordless phone), switch off this appliance or move the unit away from this appliance. -If the baby unit is switched off, switch it on. Operating range -The operating range is 330 metres/1000 feet outdoors and up to 50 metres/150 feet indoors. -The operating range of the baby monitor varies depending on the surroundings and factors that cause interference. Wet and moist materials cause so much interference that the range loss is up to 100%. For interference from dr y materials, see table below Wood, plaster, cardboard, glass (without metal, wires or lead) < 30cm (12in) 0-10% Brick, plywood < 30cm (12in) 5-35% Reinforced concrete < 30cm (12in) 30-100% Metal grilles or bars < 1cm (0.4in) 90-100% Dry materials Material thickness Loss of range Metal or aluminium sheets < 1cm (0.4in) 100% Functions and feedback on the baby unit nightlight The nightlight produces a soft glow that comfor ts your baby. 1 Press the Q button on the baby unit to switch the nightlight on or off. Lullaby function 1 Press the K button on the baby unit to play the last selected lullaby.The selected lullaby repeats for the set time. (Fig. 2) 2 Press the >| button to select another lullaby from the list. (Fig. 3) 3 To adjust the sound level of the lullaby, press the volume + or the volume – button on the baby unit (Fig. 4). Note:You can only set the loudspeaker volume on the baby unit when a lullaby is playing. If you set the volume for the lullaby higher, the sound will also be louder when you use the talk function on the parent unit. 4 To stop lullaby playing, press the K button on the baby unit. EngliSh Projector You can soothe your baby with coloured light patterns projected on the ceiling by switching on the projector. , Press the projector on/off button to switch on the projector.The projector symbol appears on the display of the parent unit (Fig. 5). There are six different patterns.The first pattern fades in to full intensity in 2 seconds. It is projected for 8 seconds and then fades out for 2 seconds while the next pattern fades in. Each pattern is projected for 10 seconds.The patterns are repeated for the set time (Fig. 6). 2 To switch off the projector, press the projector on/off button again. Paging the parent unit If you have lost the parent unit, you can use the FIND button on the baby unit to locate the parent unit.This function only works when the pa...