Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
1 2) 2.4GHz Wireless Receiver 1 3) Earphone . 1 4) Power Adapter for camera . .. 1 5) Power Adapter for receiver . 1 Note: AA Batteries are not included 2. Diagram 3. Structure 3-1. Layout of Camera 3-2. Layout of Receiver 4. Installation 4-1. Setting Up the Camera 1. Setup the camera in the desired location 2. Connect the camera to the adapter and then slide the power switch to the ON position Note: --This camera can also use dry batteries as a power source by loading 4 AA batteries into the battery compartment on the back of the camera with their polarities in the correct position. --The AC adapter will work instead of batteries after it is plugged in. If the camera is not going to be used for a long period of time, please unplug the adapter and remove the batteries. * The camera can run off of batteries for up to 5 hours (IR OFF) 3. Rotate the rounded head of the camera to the desired angle for surveillance. 4-1-1. Camera Learning Setup If there is interference from another wireless device the Learning Switch can program the unit to avoid it. Push the Learning Switch on the back of the camera from OFF to ON, then press the Eliminate button on the receiver for 3 seconds. The picture will become clearer on the screen. 4-1-2. Camera Alarm Setup 1. The camera provides a Sound Detection alarm. Sound Alarm Setup: To set up the sound alarm slide the alarm switch to the VOX position. The system will enter standby mode until a sound triggers the alarm. When sound is detected the alarm sounds for two minutes or until the Eliminate Alarm button is pressed, which will put the system into snooze mode for 35 seconds. After the 35 seconds is up the alarm will go back into standby mode until triggered by the next sound alarm event. Turn Off Alarm: To turn off the alarm slide the alarm setting switch to the Off position. The alarm function will be disabled. Note: The Sound alarm will be turned off automatically if the Eliminate Alarm button is not pressed within 2 minutes after the alarm sounds. If both the battery and A/C adapter are in use and the alarm setup failed to trigger, turn the camera and the receiver off and then back on to re-activate the alarm. 4-2. Setting Up the Receiver 1. Connect the receiver to the adapter and then slide the power switch to the ON position. Note: --This receiver can also use dry batteries as a power source by loading 4 AA batteries into the battery compartment at the back of the camera with their polarities in the correct position. --The AC adapter will work instead of batteries after it is plugged in. If the camera is not going to be used for a long period of time, please unplug the adapter and remove the batteries. * The camera can run off of batteries for up to 5 hours. 2. Adjust the volume control to the desired level. 3. Set the channel of the receiver to the same channel as the camera by pressing the channel button continuously, the pictures will display on the screen when the channels match. Note: The receiver supports up to 4 cameras working at the same time. If there are 2, 3, or 4 cameras working you can press and hold the channel button about 3 seconds to enter auto-switch-browse mode and the channels will by displayed one by one for 6 seconds at a time. 5. Specifications Item Value GENERAL Transmission Frequency ISM 2,400~2,483 MHz Transmission Power 10mW/CE; 2mW/FCC Operating Frequency 2414MHz;2432MHz;2450MHz;2468MHz Unobstructed Effective Range 100m (328ft)(Min.) Spread Spectrum/Modulation Mode FHSS/GFSK Operating Temperature -10 ~ +50(Degree C) / +14~ +122(Degree F) Operating Humidity <85%RH CAMERA Imaging Sensor Type CMOS Picture Total Pixels PAL:720.480 Pixels; NTSC: 720.576 Pixels Horizontal Resolution 380 TV Lines View Angle 55° Minimum Illumination 0Lux (IR ON) Image Resolution 320x240 @ 10fps Night Vision Range 5m Battery Working Time 5 hours (IR OFF) Motion Detection Distance 5m (16ft) Sound Control Sensitivity >65dB Consumption Current 280mA (Max.) Power Supply DC +8V Dimensions(W.D.H) 86*48*135 mm (3.5*2*5.5 in) Weight 146 g (5.2 oz) MONITOR LCD Screen Type 2.36 inches TFT-LCD Effective Pixels 480.234 Receiving Sensitivity <-85dBm Battery Working Time 5 hours Consumption Current 200mA (Max.) Power Supply DC +8V Dimensions(W.D.H) 86*54*143 mm (3.5*2.25*5.75 in) Weight 130 g (4.6 oz) * Actual transmission range may vary according to weather, Location, interference and building construction. * All the specifications are subject to minor change without prior notice. 6. FCC information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTIONS: . Do not expose the device to water or other liquids. . Turn o...