Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Please read and follow these instructions carefully to insure a proper and safe installation. Keep these instructions in a safe place for future reference. CONTENTS 1 Camera 1 Monitor 1 Charging Base 2 AC Adapters 1 Audio/Video Cable 6 AA Rechargeable Batteries 2 Mounting Screws and Anchors 1 Mounting Template 1 Instruction Manual Note: For battery operation you will need: • 6 AA batteries for video receiver (included) • 6 AA batteries for the video camera (not included) • One flat-head screwdriver (not included) Introduction.............2 Instructions............. 4 Special Features.......... 6 Maintaining Your Monitor. . . . 6 For Your Well Being........ 7 Limited Product Warranty. . . 8 Also Available........... 10 On/Off & Brightness Volume Control Control Channel Selector LCD Speaker On/Off A/V Output AC/DC Power LED Jack Indicator Monitor Stand Front of Monitor Rear of Monitor Rear of Camera 1.8” TFT LCD Display Antenna Camera Microphone 3 Power LED Indicator Infrared Night Vision Channel Selector Power On/Off Removable Belt Clip Battery Cover AC/DC Jack Voice Activation with Sensitivity Control AC/DC Jack Front of Camera IINSTRUCTIONS 4 You can power both the camera and the video receiver with batteries or an AC adapter. Each unit requires 6 AA batteries for battery operation. Both units have rechargeable circuits, therefore, when using the AC adapters, make sure you only have rechargeable batteries or no batteries at all in the battery compartment. The battery life of the rechargeable batteries is approximately 3-3 1/2 hours in the video receiver and 5 hours in the camera. For long periods of non-use, remove all batteries from their compartments and unplug the AC adapters. FOR BATTERY POWER 1. Remove the battery cover with a flathead screwdriver. The battery cover is on the bottom of the camera and on the back of the monitor. 2. Insert 6 AA alkaline or rechargeable batteries into either unit or both units matching Positive (+) to Positive and Negative (-) to Negative. For complete battery power you will need a total of 12 AA batteries (6 rechargeable batteries are included with your monitor). 3. Replace the battery cover with a screwdriver. 4. Charge the rechargeable batteries 10-12 hours before using the monitor on battery power for the first time. This can be done while operating the monitor on AC power or when the monitor is off. Charge the batteries by plugging the adapter directly into the monitor or into the monitor stand. Camera Video Monitor FOR AC POWER 1. IMPORTANT: make sure you only have rechargeable batteries or no batteries at all in the battery compartment when using an AC adapter. 2. Insert the end of one adapter into the jack marked 9V DC that appears on the side of the monitor and one into the jack marked 9V DC on the back of 5 the camera. 3. Plug the adapters into your electrical outlet. HOWTOUSE 1. Turn both units on by pressing the Power ON/OFF button on the front of the camera and by turning the ON/OFF dial on the side of the video monitor. The monitor’s ON/OFF dial is also the volume control. 2. The power indicator on the front of both units will turn on and will be green. 3. Rotate the camera head so it faces your baby. 4. Adjust the monitor’s volume with the volume control knob. 5. Select the channel that gives you the best reception. The channel selector is located on the side of the camera and on the front of the video receiver. Make sure both units are tuned into the same channel. 6. For daytime vision, place the camera up to 10 feet from your baby making sure it is out of reach. Adjust the antenna to achieve the best reception. You may also have to adjust the distance of the camera from your baby. 7. For nighttime vision place the camera no more than 6 feet from your baby making sure it is out of reach. Adjust the antenna to achieve the best reception. You may also have to adjust the distance of the camera from your baby. Remember, when using the infrared night vision the image will only be in black and white. 8. If the camera and video receiver are too close to each other you will hear static or feedback. If this happens, increase the distance between the 2 units. 9. To mount the camera on the wall, use the mounting screws and anchors using the template provided. Caution: Position the power cord out of the reach of children. SPECIAL FEATURES 6 VOICE ACTIVATION: BATTERY- SAVING FEATURE FOR CAMERA The Voice Activation dial is on the side of the camera. When this is switched on, the camera will only transmit a picture when sound is detected in the child’s room. If there is no sound your screen will be blank. You can adjust the sensitivity of this feature by turning the dial to the right or the left. The use of this feature will prolong the life of the batteries in the camera when powering the camera with batteries only. LCD ON/ OFF: BATTERY- SAVING FEATURE FOR MONITOR You can turn the screen of the video receiver off and still maintain the sound monitor function. To use th...