Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Set button. Once - will sound at one time only Everyday - will sound everyday. Weekly - will sound once every week. Weekdays - will sound on weekdays only. Weekends - will sound on weekends only. 6. Press the Tuning+/- buttons to set whether the Alarm will sound with FM radio, buzzer, Aux In, or Internet Radio. When the Alarm sound is set for FM radio or Internet Radio, the lat played station will be turned on to be the sounding. When the Alarm sound is set for Aux In, please make sure there is a sound source playing and connecting to the Aux In of this radio. 7. Press the Select button to finish the setting. When the alarm sounds 1. The radio alarm will sound at the selected times unless cancelled. The volume for the radio alarm as the volume previously used when listening to media player. If for any reason the radio cannot connect requested radio station at the time that the alarm is alarm will be used instead. 2. The buzzer alarm sounds for 60 minutes and the volume will gradually increase from a low level. 3. If a radio alarm sounds and the radio is already playing, the radio will change to the station specified for the alarm. Activate and deactivate alarms 1. When Alarm 1 is activated, “ ” is shown on the display, same as Alarm 2. 2. When the mark “ ” is shown on the display, press the Alarm 1 button to deactivate the Alarm 1, and “ ” will disappear. Same as Alarm 2. 3. To re-activate Alarm 1, press the button Alarm 1, and “ ”will be shown on the display, also the Alarm 1 information will be shown as well. 32 GB Sleep timer Your radio can be set to turn off after a preset time has elapsed. The sleep setting can be adjusted between 15 and 3 hours 15 minutes in 15-minute increments. 1. Make sure the radio is on and playing. 2. Press the Time Set button, and the display shows “Sleep Timeout”. 3. Press Tuning+/- buttons to set the required sleep time setting is selected between 15 and 3 hours 15 minutes or to Off. 4. Press the Set button to confirm the setting. The display will show ‘Zzz’. Your radio will switch off after the preset time has elapsed. 5. To cancel the sleep time before the preset time has elapsed, just press the Power button to turn off the radio. Nap timer It is a countdown alarm which will sound after you set. And the time period can be set from 10 10 minutes steps. 1. Touch the NAP key button the required time period is the display. 2. Press the Tuning+/- buttons to select the countdown alarm time. 3. Press the Select button to set the Nap timer. And the “ ” mark is shown on the display. 4. While the Nap timer is alarming, press the Power button to make it silent. 5. To cancel the Nap timer before the time Nap time is elapsed, press the NAP button, and long press it again until the mark “ ” is disappeared on the display. Backlight Press the Dimmer button to adjust the display backlight settings to suit your needs. Separate settings are available for Active mode (while operating the radio), Inactive mode (when listening), and Standby mode (when the radio is off with just the clock display showing). Language selection This facility allows you to change the display language for the menus. 1. Press the Tuning+/- buttons until it shows “Setting”, and then press the Select button. 2. Press the Tuning+/- buttons until it shows “Language”, and then press the Select button. 3. Press the Tuning+/- buttons until it shows the language you would like to select, and then press the Select button. Software version display The software version display is provided for your reference only. 1. Press the Tuning+/- buttons until it shows “Setting”, and then press the Select button. 2. Press the Tuning+/- buttons until it shows “Version”, and then press the Select button. 3. The display will show the version of the software. 4. Use the Back button to exit. Network configuration (For This menu enables you to configure your scan for a connection to an alternative wireless network, or to manually configure the network parameters. This can be useful if you take the Internet radio to another location where there is a different network setup. Configuring the radio only to use a wired Ethernet connection (For RCR-7 only) 1. Turn on the radio, and press the Tuning+/- button until the display shows