|
Facilidade de uso
Some models are designed to operate multiple receivers. A selector switch on the Transmitter determines which door will be controlled in a multi-door installation. The Receiver is connected to the commercial operator in the same manner as a 3-button station and provides open, close and stop functions via radio control. • ALLSTAR TRANSMITTERS ARE INTENDED FOR USE WITH COMMERCIAL DOOR OPERATORS ONLY. DO NOT USE FOR ANY OTHER PURPOSE. DO NOT MODIFY IN ANY MANNER. • CHECK LOCAL BUILDING AND ELECTRICAL CODES FOR MANDATORY INSTALLATION AND WIRING REQUIREMENTS. • CONNECT POWER CORDS ONLY TO A PROPERLY GROUNDED OUTLET. IF PERMANENT WIRING IS REQUIRED BY CODES, DISCONNECT POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE ATTEMPTING ANY WIRING CONNECTIONS. • DO NOT WEAR RINGS, WATCHES OR LOOSE CLOTHING WHILE INSTALLING OR SERVICING GARAGE DOOR OPENERS. WEAR SAFETY GOGGLES OR OTHER PROTECTIVE EYEWEAR. • AN UNBALANCED DOOR OR ONE THAT STICKS OR BINDS MAY CAUSE INJURY OR DEATH. ENSURE DOOR IS PROPERLY BALANCED AND ELIMINATE ANY STICKING OR BINDING. • YOUR GARAGE DOOR IS A LARGE MOVING OBJECT. THE SPRINGS, PULLEYS, CABLES AND MOUNTING HARDWARE UTILIZED TO BALANCE ITS OPERATION ARE UNDER EXTREME TENSION AT ALL TIMES AND CAN CAUSE SERIOUS PERSONAL INJURY, EVEN DEATH, IF DISTURBED. ONLY A QUALIFIED SERVICE PERSON SHOULD MOVE, LOOSEN OR ADJUST DOOR SPRINGS OR HARDWARE. • LOCATE CONTROL PUSHBUTTONS WITHIN SIGHT OF THE DOOR AND AWAY FROM THE MOVING PARTS OF THE DOOR. INSTALL ENTRAPMENT WARNING LABEL NEXT TO THE CONTROL PUSHBUTTON IN A PROMINENT LOCATION. • REMOVE ALL ROPES AND REMOVE OR MAKE INOPERATIVE ALL LOCKS CONNECTED TO THE GARAGE DOOR. • THE IMPORTANT SAFEGUARDS AND INSTRUCTIONS IN THIS MANUAL CANNOT COVER ALL POSSIBLE CONDITIONS AND SITUATIONS. IT MUST BE UNDERSTOOD THAT COMMON SENSE AND CAUTION MUST BE EXERCISED BY THE PERSON(S) INSTALLING, MAINTAINING AND OPERATING THIS EQUIPMENT. INSTALLER: Leave this manual with your customer upon completion of the installation. WARNING TO REDUCE THE RISK OF SEVERE INJURY OR DEATH: READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS! PRODUCT FEATURES IMPORTANT INSTALLATION NOTES Page 2 of 4 P/N 107343 Rev D IMPROPER WIRING COULD CAUSE ELECTROCUTION OR DAMAGE TO CIRCUITRY. WARNING FOLLOW LOCAL BUILDING AND ELECTRICAL CODES. TO PREVENT ELECTROCUTION DISCONNECT POWER AT FUSE BOX AND DOOR OPENER WARNING BEFORE WIRING PERMANENTLY. DO NOT USE RADIO CONTROLS ON COMMERCIAL DOOR OPERATORS UNLESS PROPER ENTRAPMENT PROTECTION DEVICES ARE INSTALLED. CONSULT THE MANUFACTURER OF WARNING YOUR OPERATOR FOR MORE DETAILS. The various Transmitter models are shown below. All models may be coded to work with Allstar 3-channel Receivers such as the 831R, 831RE and the 8833R. Refer to the individual instructions for proper wiring of the Receivers. Follow the directions on the next page for proper Transmitter/Receiver Coding! 733 Rotary Switch selects door A, B or C Slide Switch selects door A, B or C 8833C-OCS Rotary Switch selects door 1, 2, 3, ... or 9 639 Combination of both Rotary Switches selects door Examples: A1, B7, C9, etc. 831 STOP CLOSE OPEN 8833-OCS STOP CLOSE OPEN 535 COMMERCIAL TRANSMITTER MODELS Page 3 of 4 P/N 107343 Rev D The information below indicates how to set the coding switches in the various transmitters and receivers. IF YOU ARE USING A 8833 OCS-ECONOMY OR 831 STANDARD TRANSMITTER: Exactly match all 8 code switches in the transmitter and receiver. The code switches may be set in any random pattern of +, - and 0. IF YOU ARE USING A 8833C OCS-ECONOMY OR 733 STANDARD TRANSMITTER: This transmitter is used to control up to 3 different doors. This is accomplished by setting the selector switch on the transmitter to either A, B & C and setting the #6 coding switch in the 831 receiver . Start coding by exactly matching all 8 code switches in the transmitter and the receivers. The code switches may be set in any random pattern of +, 0 and - positions. Next, in receiver A, set code switch #6 to the + position; In receiver B set code switch # 6 to the 0 position; In receiver C set code switch # 6 to the - position. The table to the right shows the switch positions. IF YOU ARE USING A 639 STANDARD TRANSMITTER: This transmitter is used to control up to 9 different doors. This is accomplished by setting the selector switch on the transmitter to either 1, 2, 3, 4, 5, 6, 7, 8 or 9 and setting the #7 and #8 coding switches in the 831 receiver. Start coding by exactly matching all 8 code switches in the transmitter and receivers. The code switches may be set in any random pattern of +, 0 and - positions. Next, in receiver 1, set code switch #7 to + and code switch #8 +; In receiver 2, set code switch #7 to + and code switch #8 to 0. Continue setting the codes in the 831E receivers as shown in the table. IF YOU ARE USING A 535 STANDARD TRANSMITTER: This transmitter is used to control up to 27 different doors. This is accomplished by setting the selector switches to either A, B or C and either 1, 2, 3, 4, 5, 6,...
Este manual também é adequado para os modelos :Receptores de rádio - 8833C OCS (216.63 kb)