Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
• Adjust the volume. AM broadcast cannot be received properly – Weak radio signal. • Rotate the set for better reception and make sure the set is placed on a non-metallic surface. Continuous crackling and hiss noise during AM reception – Interference from other electrical equipment e.g. TV’s, computers, fluorescent lamps. • Move the clock radio away from electrical equipment. Intermittent crackling sound during FM reception – Weak signal. • Adjust the built-in power cord aerial. The alarm does not function – The alarm is not set • Set the alarm time and the alarm switch to BUZ or RAD. – Volume too low for radio. • Increase the volume. The slumber does not function – RADIO still in ON position. • Switch RADIO to OFF position. – Clock control in TIME SET or ALARM position. • Adjust clock control to RUN position. All unnecessary packaging material has been omitted. We have tried to make the packaging easy ta separate into three mono-materials: cardboard (box), expandable polystyrene (buffer), polyethylene (bags). Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packing materials, dead batteries and old equipment. ENVIRONMENTAL INFORMATION Troubleshooting CANADA English: This digital apparartus does not exceed the Class B limits for noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. Francais:Cet appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de Classe B prescrites dans le Regelement sur le Brouillage Radioelectrique edicte par le Ministere des Communications du Canada. 1. Check if the mains voltage as shown on the type plate on the base of the set corresponds to your local power supply. 2. Connect the power plug into the wall outlet. The power supply is now switched on and the numbers on the display will start to flash. You will need to set the correct time. 3. To disconnect the set from the power completely, withdraw the power plug from the wall outlet. You can use the clock radio solely as a radio. 1. Set the RADIO switch to ON. 2. Select your waveband using the BAND switch. 3. Use TUNING to find your radio station. 4. Adjust the sound with the VOLUME control. 5. To turn off the radio, set the RADIO switch to OFF. To improve radio reception – For AM, the set is provided with a built-in antenna which to function best should be placed on a non-metallic surface e.g. wood, plastic. Direct the AM antenna by adjusting the position of your clock radio. – For FM reception there is an antenna wire built-in into the power cord. You should adjust the power cord slightly to obtain optimum reception. Clock display The time is displayed using the 12-hour clock system where the PM indicator lights up (on = PM, off = AM) in the top left corner of the display. Important! When setting the clock alarm time, for accurate hour and minute adjustment always make sure you press the HR and MIN buttons separately and not simultaneously. Adjusting the time 1. Adjust the CLOCK control to the TIME SET position. 2. Press and hold down the HR or MIN buttons to set and adjust both the hours and the minutes. – With your finger held down on HR, the hour will increase, shown as a digit from 00 to 12. – With your finger held down on MIN, the minutes will increase, shown as a digit from 00 to 59. 3. Release the HR or MIN button when you have reached the correct setting. 4. To safeguard the clock time from being accidentally adjusted, turn the CLOCK control to the RUN position. 6 : 45 CLOCK FM/AM RADIO MAINS CONNECTION Installation/Radio Clock Slumbering Additional Information General If you wish to use the alarm, then you should first set the alarm time. There is a choice of two modes for waking you up: by buzzer or radio. The display also indicates whether you have switched on the alarm, shown as a dot next to ALARM in the display. 1. Adjust the CLOCK control to the ALARM position. 2. Press and hold down the HR or MIN buttons to set and adjust both the hours and minutes. – With your finger held down on HR, the hour will increase, shown as a digit from 00 to 12. – With your finger held down on MIN, the minutes will increase, shown as a digit from 00 to 59. 3. Release the HR or MIN buttons when you have reached the correct setting. 4. Adjust the CLOCK control to the RUN position to return to clock time display. – To review your set alarm time, adjust the CLOCK control to the ALARM position. 5. To select the alarm mode you wish to be awoken by, set the respective ALARM switch to RAD or BUZ. – If you have selected the radio mode, make sure you have adjusted the volume loud enough to wake you. – The buzzer is set at a fixed volume and cannot be adjusted. You can switch off the alarm in three ways. Unless you choose to cancel the alarm completely, the ALARM RESET option will be automatically se...
Este manual também é adequado para os modelos :Relógios - AJ3081/17 (423.13 kb)