Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
8. Attachments – Do not use attachments not recommended by the product manufacturer. 9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage to the product due to lightning and power-line surges. 10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 11. Damage Requiring Service – The unit should be serviced by qualified service personnel when: A. the power supply cable or plug has been damaged. B. objects have fallen into or liquid has been spilled into the enclosure. C. the unit has been exposed to rain. D. the unit has been dropped or the enclosure damaged. E. the unit exhibits a marked change in performance or does not operate normally. 12. Antenna – Do not connect an external antenna to the unit (other than that provided). 13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the power cable should be unplugged from the unit to prevent damage or corrosion. 14. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel. Questions? Visit 9 Troubleshooting Possible Problem Solution Symptom iP43 does not turn on AC adaptor isn't plugged into a working wall Plug the AC adaptor into a working wall socket and plug the socket or not plugged into the power supply connector into the supply jack on the unitjack on back of the unit iP43 doesn’t respond If unit is plugged in and doesn't respond, try resetting the unit by following these steps: a) remove iPhone/iPod from dock b) unplug unit from power source c) remove back up batteries d) wait a few minutes, then resume use iP43 requires a reset Remove your iPhone/iPod from the dock and check for obstruction on the connectors in the dock and on your iPhone/iPod. Then reseat it in the dock. iPhone/iPod is not docked properly Battery Low icon Batteries are weak Replace with new batteries always flashing Batteries were not installed properly Check to make sure the polarity ( + and – ends) matches the diagram in the battery compartment iPhone/iPod does iPhone/iPod is not docked properly Remove your iPhone/iPod from the dock and check for not respond to the obstruction on the connectors in the dock and on your iPhone/iPod. Then reseat it in the dock. unit/iPod is playing but no sound comes Your iPhone/iPod software is too old Upgrade software on your iPhone/iPod via iTunes on your computer out iPhone/iPod is locked up/plays but no Check the volume setting. Make sure your iPhone/iPod is working sound comes out properly before docking into the unit. Please refer to your iPhone/iPod manual for details. See above for software upgrade information. You may need to reset your iPhone/iPod. Refer to your iPhone or iPod user guide for details on how to perform a reset. Using 1st or 2nd generation iPod, iPod iP43 cannot control those iPod models or other devices. Shuffle or other devices. iP43/iPhone/iPod The iP43 is reacting to external interference Move unit away from potential sources of external interference such performance is erratic as computers, modems, wireless devices (routers) or fluorescent light. Volume is set too low on iP43 Make sure volume is turned up No sound from iP43 iPhone/iPod iPhone/iPod is not docked properly Remove your iPhone/iPod from the dock and check for didn’t obstruction on the connectors in the dock and on your charge up iPhone/iPod. Then reseat it in the dock. Please make sure your iPhone/iPod is working properly before docking into the unit. Please refer to your iPhone/iPod manual for iPhone/iPod battery has problem iPhone/iPod is locked up/ frozen details. 10 Troubleshooting Symptom Possible Problem Solution Sound is distorted Volume level is set too high Decrease the volume Sound source is distorted If the iPhone/iPod original sound source (MP3) is old or of poor quality, distortion and noise are easily noticed with high-power speakers. Try updating the sound file from a trusted source such as iTunes. If you are using an external sound source like older generation of iPod or iPod Shuffle, try reducing the output volume on the device itself. Also try turning bass boost OFF. EQ settings are too high. Lower EQ settings. Unit/adaptor gets warm after extended play at high volume This is normal Turn unit off for a while or lower volume Snooze time is too long/short Custom snooze time not set Press and hold Snooze button then turn Set Wheel to adjust Alarm not working AM/PM time/alarm time not set correctly When setting clock or alarm time, take note of the AM/PM indicators Alarm time or source selected for alarm 2 or ...
Este manual também é adequado para os modelos :Receptores de rádio - IP43 (240.88 kb)