Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
1. Read these instructions 2. Keep these instructions 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with these instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 10. Only use attachments / accessories specified in these instructions. 11. Unplug this apparatus during lightning storms or when unused for long periods of time. 12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 13. This appliance shall not be exposed to dripping or splashing water and that no object filled with liquids such as vases shall be placed on the apparatus. 14. Do not attempt to dismantle, open or repair this product yourself. If a fault occurs, seek advice from your local qualified service technician or contact the distributor via the telephone number at the back of this instruction manual. 1 PROTECT YOUR FURNITURE!! PROTECT YOUR FURNITURE!! This system is equipped with non-skid rubber ‘feet’ to prevent the product from moving when you operate the controls. These ‘feet’ are made from non-migrating rubber material specially formulated to avoid leaving any marks or stains on your furniture. However certain types of oil based furniture polishes, wood preservatives, or cleaning sprays may cause the rubber ‘feet’ to soften, and leave marks or a rubber residue on the furniture. To prevent any damage to your furniture we strongly recommend that you purchase small self-adhesive felt pads, available at hardware stores and home improvement centers everywhere, and apply these pads to the bottom of the rubber ‘feet’ before you place the product on fine wooden furniture. FUNCTIONS AND CONTROLS 2 POWER SOURCE POWER SOURCE This AM/FM Dual Alarm Clock Radio operates on AC 240V~ 50Hz line power supply. 2 ‘AA’ (UM-3) alkaline batteries (Not included) are also required to retain the normal and alarm time settings in the event of a power outage. AC OPERATION Plug the AC Power Cord into the AC 240V~ 50Hz power source. BACKUP BATTERY INSTALLATION 1. Open the Battery Compartment Door. Following the polarity diagram shown in the Battery Compartment, insert 2 new ‘AA’ size (UM-3) alkaline batteries. 2. Replace the Battery Compartment Door. IMPORTANT: Be sure that the batteries are installed correctly. Wrong polarity may damage the unit. BATTERY CARE i. An Alkaline-type battery is recommended. For optimum performance, the batteries should be replaced every 6 months. ii. If the unit is not to be used for an extended period of time, remove the batteries. An old or leaking battery can cause damage to the unit and will void the warranty. iii. a) Do not mix old and new batteries. b) Do not mix alkaline, standard (carbon-zinc) or rechargeable (Nickel-Cadmium) batteries. iv. Do not try to recharge a battery that is not intended to be charged. The battery can overheat, rupture and leak. (Follow battery manufacturer’s directions). v. Do not dispose of batteries in fire, batteries may leak or explode and cause personal injury. POWER FAILURE INDICATOR If no battery is installed or if the battery installed is weak or dead, the time and alarm settings will be lost if the power is interrupted. When the AC power is restored the Display will show “AM 12:00”. This indicates that the time displayed is incorrect and needs to be reset. IMPORTANT: After you have reset the time, be sure to reset your alarm settings as well. 3 TIME SETTING TIME SETTING NOTE: The clock has to be set when you first plug it in. The following procedure illustrates the setting of the Clock using 7:30 PM as an example time. 1. Connect the AC cord to an AC 240V~ 50 Hz power outlet. The LCD will show “AM 12 : 00” Note: Make sure to use an outlet that is always “live”. Do not use an outlet that is controlled by a wall switch. 2. For best viewing, press the BRIGHTNESS Button (# 14) once to turn on the LCD back-light. Press the BRIGHTNESS Button (# 14) again the LCD- back light will become brighter. To obtain the maximum brightness, press the BRIGHTNESS Button (# 14) the third time. Pressing the BRIGHTNESS Button (# 14) again will turn the back light off. 3. Set the Clock Set Selector (# 18) to the “TIME” position. “AM 12:00” will blink. While “AM 12:00” is blinking, press and hold the TIME SET ! or " Buttons (# 15 or # 16) to adjust the time. The Hour and Minute digits will advance forward or backward rapidly. 4. Keep pressing and re...