Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
USING SMART TALK™ SETTING THE SLEEP SOUND 1. Start by saying the trigger word “Smart Talk” or press the Snooze Bar (#11). 2. The unit will reply “Yes” and will wait for your next command. 3. Say “Play Sleep Sound” and the unit will reply “To Choose a Sleep Sound, Say Ocean, Rain, Brook or Radio”. 4. Say “Ocean, Rain, Brook or Radio”. You can also say the command “Cancel” during this step if you wish to cancel setting the sleep sound and the unit will reply “OK” to confirm. 5. When the sleep sound is successfully understood, the sleep sound chosen will show on the display (#27) and be played for the selected sleep time. 6. If the unit fails to understand the sleep sound given, it will reply “Please Repeat”. Now repeat step #4 above. ACTIVATE SLEEP MODE AND SETTING SLEEP TIME 1. Start by saying the trigger word “Smart Talk” or press the Snooze Bar (#11). 2. The unit will reply “Yes” and will wait for your next command. 3. Say “Sleep Time” and the unit will reply “Please choose a Sleep Time, say Fifteen, Thirty, Forty-Five or 60 Minutes”. 4. Say “Fifteen, Thirty, Forty-Five or 60 Minutes”. You can also say the command “Cancel” during this step if you wish to cancel setting the sleep time and and the unit will reply “OK” to confirm. 5. When the sleep time is successfully understood, the unit will say “Your Sleep Sound will turn off in … Minutes”. The number you chose in step #4 will be said. 6. The sleep time chosen will also show on the display (#24) and be played for the selected Sleep Time. E-18 NOTE: - During sleep, you may press the SLEEP BUTTON (#10) to check the remaining sleep time. - When sleep sound is playing, its volume can be adjusted from low to high (level 1-4) by pressing the > (UP) (#6) or < (DOWN) (#4) BUTTONS. The selected sleep sound volume will be displayed. - To change the sleep sound during sleep, press the SNOOZE BAR (#11) and use “Play Sleep Sound” voice command to change it as usual. The remaining sleep time will not be affected. LISTENING TO RADIO 1. Select your desired radio band using the BAND SELECTOR (#7) for AM or FM. 2. Press the ON/OFF BUTTON (#12) to turn radio on. 3. Rotate the TUNING CONTROL (#9) to your desired radio station according to the dial scale on the unit. 4. Rotate the VOLUME CONTROL (#1) to adjust to the desired output level. 5. To turn off the radio, press the ON/OFF BUTTON (#12). TIPS FOR BEST RECEPTION AM – The AM antenna is located inside the cabinet of the unit. If AM reception is weak, change the position of unit until the internal antenna picks up the strongest signal. FM – During FM reception, always keep the FM WIRE ANTENNA (#21) fully extended for best performance. However, if FM reception is weak, try repositioning the unit near an open window until you get the best reception. USING THE LINE IN TO LISTEN TO EXTERNAL AUDIO PLAYER You may playback your favorite music from your iPod or a portable digital audio player using the Line in function. 1. Connect the headphone jack of your external device to the LINE IN JACK (#18) at the rear cabinet of this unit using a stereo cord with a 3.5mm phone plug on either ends. (Note: the stereo cord is not included). E-19 2. Press the ON/OFF BUTTON (#12) to turn on the radio. It will automatically switch to Line In mode when a suitable stereo cord is correctly connected. 3. Start playing your external audio device. 4. Slowly increase the volume control of the unit until the desired level is obtained. To avoid output sound distortion due to overloading, you may need to lower the volume output of your audio device. Note: the stereo music from your audio device will be converted to a monaural audio output. 5. Turn off your external audio device first when you finish listening. 6. Then unplug the stereo cord from the LINE IN JACK (#18) and normal radio reception will resume. DIMMER CONTROL MANUAL SETTING The display HI/LO DIMMER BUTTON (#19) is located on the back of the unit. Pressing it will toggle between bright and dim backlight options for the display. USING SMART TALK™ 1. Start by saying the trigger word “Smart Talk” or press the Snooze Bar (#11). 2. The unit will reply “Yes” and will wait for your next command. 3. Say “Display” and the unit will reply “Say Display Low or Display High”. 4. Say “High” or “Low” to set the display brightness accordingly. You can also say the command “Cancel” and the display will stay at it’s current setting. 5. If you do not say the command word correctly, the unit will prompt you to repeat or start all over again. RESETTING THE UNIT After you have installed backup batteries and connected the unit to AC power source for the first time, we recommend you to press the RESET Button (#15) at the bottom of the cabinet to correctly initialize it. E-20 In case of an erroneous display or prolonged abnormal behavior during normal use, you can also safely restore it to its factory preset conditions by pressing the RESET Button (#15). Please note that all personal settings including current time, ...