Assessments - 3, GPA: 3
(
)
)
|
Facilidade de uso
NOTE Light will fade-in (gradually increase in brightness to maximum) 20 minutes prior to set alarm time. Light Will stay on (even after SNOOZE has been activated) after set alarm time for 60 minutes. SLEEP TIMER To adjust sleep timer setting: 1. Turn on desired option: OPTION PRESS: Radio RADIO Light LAMP Nature sound NATURE SOUND 2. Press SLEEP to activate. 3. Press SLEEP repeatedly to change the sleep timer setting (120, 90, 60, 30, 15, 0 min). After 5 seconds of inaction, the timer will automatically be confirmed and set. TIP Press SLEEP again to change sleep timer (120, 90, 60, 30, 15, 0 min). NOTE Ensure radio or sound and/or light has been selected to activate sleep timer. NOTE If light option has been chosen for sleep timer, light will fade out. READING LAMP To turn on / off light: • Press LAMP. To adjust level of brightness: • Press / to increase or decrease brightness. TIP Press and hold / to rapidly change level of brightness (1-20). For your convenience, the level of brightness will be stored in memory for the next time reading lamp is turned on. NOTE Do not look directly at the light. PLAYING MUSIC Using a cable, plug one end to your music storage device and one end to AUDIO LINE-IN located at the back of unit. When cable has been successfully connected, will be displayed on the LCD screen and sound will emit from speakers. To adjust brightness: • Slide DISPLAY BRIGHTNESS switch to LOW / HIGH. RESET 1. Remove and reinsert the batteries. 2. Press RESET to return to the default settings. SPECIFICATIONS TYPE DESCRIPTION MAIN UNIT L x W x H 257 x 199 x 140 mm (10.12 x 7.84 x 5.51 in) Weight 1386 g (13.6 oz) without battery FM 87.5 to 108 MHz Power Input: AC 230V 50Hz (EU version) Input: AC 120V 60Hz (US/Canada version) 2 x UM-4 (AAA) 1.5V batteries (for backup) NOTE • Connection type of the switch: . • Range of lamp load: (Lamp) 20W - 60W • The apparatus shall not be exposed to dripping or splashing. • To be completely disconnect the power input, the mains plug of apparatus shall be disconnected from the mains. • The mains plug of apparatus should not be obstructed OR should be easily accessed during intended use. • No naked flame sources such as lighted candles should be placed on the apparatus. 4 EN TROUBLESHOOTING The below table lists out some of the problems you could encounter. If you are unable to solve the problem, contact the Customer Care Centre in your country. Contact us via www2.oregonscientific.com/service/support.asp Problem Possible cause Solution / Remarks The unit does not work Power supply? Ensure plug has been properly inserted into the wall socket Ensure there is no power failure. Check by connecting another appliance to the wall socket The unit does not work Normal use This is normal as the light bulb generates heat. However, ensure there is enough ventilation and vents are not covered as this can pose a fire hazard. When setting functions, the unit does not respond Normal use Press RESET at the base of the unit or remove and reinsert plug into wall socket. The appliance will then be reset to factory default settings. The light does not work Light intensity is too low? Alarm function disabled? Light bulb is defective? Light bulb not properly screwed in? Press to increase light intensity Ensure alarm time is displayed on LCD screen. Press ALARM to enable. Replace the light bulb. Unscrew and screw in the light bulb again. Lamp does not turn on again immediately after it has been switched off Normal operations Allow 3 seconds for the lamp to dim. Please wait until the lamp reaches the preset intensity level No sound when the alarm goes on Alarm function disabled? Radio is defective? Ensure alarm time is displayed on LCD screen. If -:- - is displayed, press ALARM to enable. If radio has been selected for alarm mode, check that radio works. Press RADIO after you disable the alarm or press ALARM. The radio is defective / produces a crackling sound Positioning of external antenna? Broadcast signal is weak? Change position of external antenna if necessary. Press RADIO TUNE to search for the correct signal. Alarm did not activate today, but it did yesterday Alarm function disabled? Power failure? Ensure alarm time is displayed on LCD screen. If -:- - is displayed, press ALARM to enable. Perhaps there was a power failure which lasted longer than the capacity of the back up system? The display will show an incorrect time and alarm will be 00:00. Do settings again. The light wakes me too early / late Location of unit is not suitable? It is recommended that the unit is not placed too far and not lower than your head while in a sleeping position. Make sure the light is not blocked by bed, duvet or pillow. Snooze does not work Distance? Wave your hand in front of the SNOOZE SENSOR at a distance range of approx. 1cm to 8cm (0.5 to 3 in). LCD backlight is too weak to see Display brightness? Slide DISPLAY BRIGHTNESS to HIGH. There is no sound after plugging to an external source External device...
Este manual também é adequado para os modelos :Receptores de rádio - WS902 (984.15 kb)