Assessments - 4, GPA: 4 ( )

Fabricante : Blaupunkt Arquivo Tamanho: 1.18 mb Arquivo Nome : Língua de Ensino:

After removing the flip/release panel, the unit switches itself off. All the current settings are saved. . If there is a CD in the unit, it remains there. Attaching the flip/release panel . Slide the flip/release panel from left to right into the unit guide. . Press the left side of the panel into the unit until it slots into place. Note: . Do not press against the display while attaching the flip/release panel. If the device was switched on when the panel was removed, it will switch itself back on automatically with the last settings (radio, Cassette, CD-changer or AUX) as soon as the panel is replaced. SWITCHING ON/OFF Switching on/off There are various ways of switching the car radio on and off, as described below. Switching on/off using the ignition If the car radio is correctly connected to the ignition and has not been switched off using the button 3, it is switched on/off simultaneously with the ignition. You can also switch on your car radio when the vehicle ignition is off. . To do so, press the button 3. Note: . To protect the vehicle battery, the unit switches off automatically after one hour. Switching on/off using the flip/ release panel . Remove the flip/release panel. The unit switches itself off. . Replace the flip/release panel once more. The device switches on. The most recent setting (radio, Cassette, CD-changer or AUX) is restored. Switching on/off using the button 3 . To switch the unit on, press the button 3. . To switch the unit off, hold the button 3 down for more than two seconds. The car radio is now switched off. Switching on by means of cassette insertion If there is no cassette in the deck when the device is switched off, . press the button, 9. The flip-release panel opens. . Insert the cassette with the open side to the right gently into the drive until you can sense some resistance. The cassette is automatically drawn into the drive. As the cassette is drawn in, it must neither be held back nor assisted. . Close the panel with gentle pressure until you feel it engage. The device switches on. Cassette play starts. ENGLISH 31 VOLUME ADJUSTMENT Volume adjustment The system volume can be adjusted in steps from 0 (off) to 66 (maximum). . To raise the system volume, turn the volume control 2 to the right. . To lower the system volume, turn the volume control 2 to the left. Setting the switch-on volume You can set the volume at which you wish the car radio to play when switched on. . Press the MENU button 8. . Press the or button : repeatedly until “ON VOLUME” appears on the display. . Use the buttons : to set the switch-on volume. If you select the “0” setting, the volume played before the unit was last switched off will be reactivated. Note: . To protect your hearing, the power- on volume is limited to a value of “38”. If the volume level was higher when the unit was switched off, the volume will be reset to “38” when the unit is switched on again. When you have finished making your changes, . press the MENU button 8 or OK ; twice. Mute setting This feature enables you to lower the system volume instantaneously (mute). . Briefly press button 3. “MUTE” appears on the display. Activating the mute setting The unit's mute level is adjustable. . Press the MENU button 8. . Press the or button : repeatedly until “MUTE LEVEL” appears on the display. . Use the buttons : to set the mute level. . When you have completed the setting, press either the MENU button 8 or OK ; twice. Telephone Audio/Navigation Audio If your car radio is connected to a mobile telephone or navigation system, then when the telephone is taken “off the hook”, or when the navigation system is speaking, the car radio is muted. The telephone conversation or speech output are reproduced via the car radio speakers. This requires the mobile telephone or navigation system to be connected to the car radio as described n the installation instruction .Your Blaupunkt dealer can tell you whi h navigation systems can be used wi h your car radi . If a traffic announcement is receiv d during a telephone call, or while t e navigation system is speaking, the tra VOLUME ADJUSTMENT ffic announcement is not reproduced until the call or the speech output has finished. If a call is received or if the navigation system begins speaking during a traffic announcement, the announcement is reproduced. The telephone call or speech output can be heard when the traffic announcement has finished. The volume at which navigation output or telephone calls start is adjusted as follows: . Press the MENU button 8. . Press the or button : until “TEL/NAVI VOL” appears in the display. . Set the desired volume with the buttons :. . When the setting process is complete, press the MENU button 8 or OK ; twice. Note: You can adjust the volume level of telephone calls and of speech output as they are made with the volume control 2. Setting the volume for the confirmation tone If you hold down a button for longer than two seconds when using certain functions, e.g. s...

Baixe o seu

Para fazer o download, introduza 2 dígitos :