Assessments - 3, GPA: 4 ( )

Fabricante : Campbell Hausfeld Arquivo Tamanho: 1.19 mb Arquivo Nome : Língua de Ensino:

Avoid using the nailer when the magazine is empty. Accelerated wear on the nailer may occur. Clean and check all air supply hoses and fittings before connecting the nailer to an air supply. Replace any damaged or worn hoses or fittings. Tool performance or durability may be reduced. Air compressors providing air to the nailer should follow the requirements established by the American National Standards Institute Standard B19.3-1991; Safety Standard for Compressors for Process Industries. Contact your air compressor manufacturer for information. NOTICE Operating Instructions ! WARNING NS219000 NS289100 NS289500 NS349000 • REQUIRES (SCFM with 16 nails 4.1 4.1 4.1 4.1 per minute @ 90 psi) • AIR INLET 1/4” NPT 1/4” NPT 1/4” NPT 1/4” NPT • NAIL LENGTH RANGE 2” to 31.2” 2” to 31.2” 2” to 31.2” 2” to 31.2” • NAIL SHANK 0.113” to 0.113” to 0.113” to 0.113” to RANGE 0.131” 0.131” 0.131” 0.131” • MAGAZINE CAPACITY 60-75 75-105 75-105 75-105 • WEIGHT 8 lbs. 5 oz. 8 lbs. 15 oz. 7 lbs. 5 oz 8 lbs. 11 oz. • LENGTH 19.5” 21.75” 21.75” 19.75” • HEIGHT 15” 15” 15” 15” • MAX PRESSURE 120 psi 120 psi 120 psi 120 psi • PRESSURE RANGE 70 - 120 psi 70 - 120 psi 70 - 120 psi 70 - 120 psi Nailer Components And Specifications 7-Sp Modelos NS219000, NS289100, NS289500 y NS349000 Adjustable Direction Exhaust Deflector Threaded Hole/Tool Balancer (M8 x 1.25) Nail Loading Area Magazine Single Cycle Trigger Warning Labels Nail Discharge Area Work Contact Element Notas 3 Operating The Nailer Read this manual and understand all safety warnings and instructions before operating the nailer. LUBRICATION This nailer requires lubrication before using the nailer for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis. The work surface can become damaged by excessive lubrication. Proper lubrication is the owner’s responsibil- ity. Failure to lubricate the nailer properly will dramatically shorten the life of the nailer and void your warranty. 1. Disconnect the air supply from the nailer to add lubricant. 2. Turn the nailer so the air inlet is facing up. Place 4-5 drops of 30 W nondetergent oil into air inlet. Do not use detergent oils, oil additives, or air tool oils. Air tool oils contain solvents which will damage the nailer’s internal components. 3. After adding oil, run nailer briefly. Wipe off any excess oil from the cap exhaust. NOTICE REMOVING NO-MAR DECKING TIP 1. Disconnect air supply from nailer. 2. Remove all fasteners from magazine (See UNLOADING THE NAILER). 3. Remove no-mar tip retaining ring. 4. Pry nomar tip away from the work contact element. 5. Replace retaining ring onto no-mar tip, then store tip in safe place for future use. INSTALLING NO-MAR DECKING TIP 1. Disconnect air supply from nailer. 2. Remove all fasteners from magazine (See UNLOADING THE NAILER). 3. Remove retaining ring from no-mar tip. RECOMMENDED HOOKUP 1. The air compressor must be able to maintai...

Baixe o seu

Para fazer o download, introduza 2 dígitos :