Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
. The battery is low. Replace the battery. Remove the old battery and install a new one. The CD, radio or buzzer alarm does not sound at the preset alarm time. . Hasn’t “ALARM A” or “ALARM B” in the display gone out? The CD or radio alarm is activated but no sound comes on at the preset alarm time. . Has VOLUME been adjusted ? The CD player does not operate. . Did you close the CD compartment lid? . Did you insert the disc correctly? The disc should be inserted with the label side up. . Dusty or defective disc — Clean the disc with an optional cleaning cloth. Wipe the disc from the center out. . Take out the CD and leave the CD compartment open for about an hour to allow condensation to evaporate. Sporadic loss of sound during CD operation. . Dusty or defective disc — Clean or replace the disc. . Excessively high volume — Reduce the volume. . Strong vibration. No sound comes from the speakers. . Has VOLUME been adjusted ? Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 8–ohm loads, both channels driven from 150 – 10 000 Hz; rated 0.8 W per channel-minimum RMS power, with no more than 10% total harmonic distortion in AC operation. CD player section System: Compact disc digital audio system Laser diode properties: Material: GaAlAs Wavelength: 785 – 800 nm Emission duration: Continuous Laser output: Less than 44.6 .W (This output is the value measured at a distance of about 200 mm from the objective lens surface on an optical pick-up block with a 7-mm aperture.) Number of channels: 2 Frequency response: 20 – 20 000 Hz +1–2 dB Wow and flutter: Below measurable limit Radio section Frequency range: FM: 87.5 – 108 MHz AM: 530 – 1 710 kHz Antennas: FM: FM wire antenna AM: Built-in ferrite bar antenna General Time display: 12-hour system Speaker: 50 mm (2 inches) diam., 8 ., cone type (2) Input: Built-in audio cable with stereo-mini plug (1): minimum input level 245mV, impedance 47 k. Power outputs: 1 W + 1 W (at 8 ., 10% harmonic distortion) Power requirements: 120 V AC, 60 Hz For power backup: 3 V DC, one CR2032 battery Dimensions: Approx. 170 . 136 . 204 mm (w/h/d) (Approx. 6 3/4 . 5 3/8 . 8 1/8 inches) incl. projecting parts and controls Mass: Approx. 1 700 g (3 lb 12 oz) incl. CR2032 battery Design and specifications are subject to change without notice. 2-899-053-21(1) FM/AM CD Clock Radio Operating Instructions Owner’s Record The model number and the serial number are located on the bottom. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. ICF-CD7000 Serial No. No Power No problem is a trademark of Sony Corporation. Dream Machine is a trademark of Sony Corporation. ICF-CD7000 © 2007 Sony Corporation Printed in China This unit includes a preinstalled Sony Lithium battery (CR2032) as back-up power source for the clock, which is preset to EST (Eastern Standard Time) at the factory. And this battery is considered part of the product. The PRESET TUNING 3 button has a tactile dot. The CD . button has a tactile dot. FM wire antenna AC power cord SNOOZE/BRIGHTNESS Built-in audio cable Battery compartment AUDIO IN VOLUME +/– .PUSH OPEN/CLOSE The VOLUME + button has a tactile dot. . . . . Push Lift up with your finger About the Backup Battery To keep good time, this unit contains one CR2032 battery inside of the unit as a backup power source. The battery keeps the clock operating in the event of a power interruption. Knowing when to replace the battery When the battery becomes weak, “.” appears in the display. If a power interruption occurs while the battery is weak, the current time and alarm will be initialized. Replace the battery with a Sony CR2032 lithium battery. Use of another battery may cause a fire or explosion. Note If “AM 12:00” flashes in the display when the unit is connected to AC outlet for the first time, the battery may be weak. In this case, consult your Sony dealer. Replacing the battery 1 Keep the AC plug connected to the AC outlet and use a screwdriver to remove the screw that secures the battery holder at the bottom of the unit. (See Fig. .-.) 2 Push the exhausted battery out from the bottom of the battery holder and insert a new battery with the . side facing up. (See Fig. .-.) 3 Insert the battery holder back into the unit and secure it with the screw. (See Fig. .- .) 4 Press RADIO ON.BAND to turn “.” off in the display. Note When replacing the battery, do not disconnect AC plug from AC outlet. If you do, the current time, alarm and NAP timer will be initialized. Battery Warning If the unit is to be left unplugged for a long time, remove the battery to avoid undue battery discharge and damage to the unit from battery leakage. NOTES ON THE LITHIUM BATTERY . Dispose of the used battery promptly. Keep the lithium battery out of the reach of children. Should the battery be swallowed, consult a doctor immediately. . Wipe the battery with a dry cloth to assure a good c...