Assessments - 5, GPA: 4.2
(
)
)
|
Facilidade de uso
Determine which spacers and screws to use OVERHANG Once you have your overhang measurement, look at Table 1 and find the nearest Measure this distance to measurement in the Overhang column, then determine the combination of spacers select screw and spacer and screw size you need. Set them apart. combination (see chart) Examples: If your cabinet has no overhang, just use 4 of the 3 inch screws with no spacers If your cabinet has a 1 inch overhang, use 4 of the 1/2" spacers, Table 1: SPACER/SCREW SELECTION CHART OVERHANG SPACERS SCREW 0 - 3/8’’ None 3’’ x 4 1/2 - 3/4’’ 1’’ spacer x 4 3’’ x 4 7/8 - 1 3/8’’ 1/2’’ spacer x 4 + 1’’ spacer x 4 4 1/2’’ x 4 1 1/2 - 1 3/4’’ 1’’ spacer x 8 4 1/2’’ x 4 1 7/8 - 2 1/4’’ 1/2’’ spacer x 4+ 1’’ spacer x 8 4 1/2’’ x 4 Note: This unit is designed for cabinets please call a customer service at 1-800-228-2792. 8 iH36 Mounting/Installation Instructions MOUNTING THE iH36 We recommend the unit be mounted flush to the front edge of the cabinet. 1. Select and Set Template and Drill holes a. Using a Template First, decide which mounting method/template you prefer, the inside the cabinet template (Mounting Template A) or the under the cabinet template (Mounting Template B). Next, cut out the selected template on the line indicated depending on whether your cabinet has an overhang or not. Position either inside or under the cabinet with the arrow facing the front of the cabinet. Secure in place with tape. b. Drilling There are 4 guide holes on the mounting template. We recommend that you start each hole before drilling by first marking the center point of the guide hole then pressing an awl or nail into the mark. Always wear safety goggles when operating a drill. For ease and accuracy of drilling, it's a good idea to use a sharp 1/4" drill bit to carefully drill 4 holes through the cabinet. Make sure all holes are drilled straight, and not at an angle. Remove any debris. c. Remove the template DRILLING TIPS: You may first wish to place masking tape over the opposite drilling to avoid splintering. Hold drill firmly to avoid the bit "walking". 2. Insert Spacers a. Place the needed spacers into the mounting posts 3. Mount unit to cabinet a. From inside the cabinet, place a finishing washer the 4 screws through any spacers into the mounting holes the unit is supported until the screws are tightened. NOTE: For secure mounting, the screws must go into the iH36 at least OPTION: You may prefer to countersink the drilled holes inside the cabinet if you have the correct countersink attachment This will make the screw Spacers heads flush with the cabinet b. Tighten the screws using a Phillips head CAUTION: DO NOT USE POWER Once the unit its mounted, plug outlet. Note that is a built-in cord wrap on the back the unit to wrap 9 Getting Started Thank you for purchasing the iHome iH36 kitchen Stereo System for your iPod. Designed specifically to work with your iPod or Shuffle, this system provides high quality audio and radio performance that invites your music to come out and It also has a factory preset clock with the correct time already preset at the factory so you just need a few steps to make it work. Please read the instructions carefully before operating the appliance and keep it for future reference. Install AC Power Plug the AC cord into wall outlet. AC power cord should connect directly to a wall outlet. Wind up the AC cord to keep it from hanging down and contacting hot cooking appliances. Install iPod Insert Your iH36 comes with 3 removable inserts and a rubber pad to ensure your iPod fits properly in the iPod drawer. Please see below table to insert/replace rubber pad to fit your iPod. Shuffle Mini Insert Thin iPod Insert Thick iPod (no Insert needed) Nano Insert 5G iPod iPod with video Dock into the Shuffle connector located in the bottom of the unit Use with iPod Mini iPod 3G 10/15/20GB iPod 4G 20 GB iPod Photo 20/30 GB iPod 3G 30/40GB iPod 4G 40 GB iPod Photo 60 GB iPod Nano 2/4GB Replace rubber pad per instruction on the 5G rubber pad card To place an insert: 1. Select the insert for your iPod insert/rubber pad ensures a proper fit for your iPod. 2. Press the Dock Open/Close Button to open the iPod dock and (Please note that iPod Note: If for any reason the iPod dock etc), simply pull on the Manual Dock Release located near at the top 10 Getting Started Install/Replace Backup Batteries If Backup Batteries are installed and a power failure occurs or the AC cord is accidentally disconnected, the current time and radio preset station settings will be temporarily maintained. Otherwise, you must reset the time and radio preset station settings. Three backup batteries are installed in the unit before shipping to keep the clock running. If the unit has no display or the Battery Low Icon (located on the right of the display) is on, replace backup batteries. 1. Please make sure the AC cord is connected; otherwise all settings may be lost during battery replacement. 2. Open the battery compa...
Este manual também é adequado para os modelos :Receptores de rádio - iH36 (182.29 kb)