|
Instruções de Operação Denon, Modelo TU-1510AE
Fabricante : Denon
Arquivo Tamanho: 1011.84 kb
Arquivo Nome : TU1510AEE2_ENG_IM_007.pdf
Língua de Ensino: 
|
 
|
|
|
Ir para baixar
Facilidade de uso
This function provides memory storage when the power operation switch is off and with the power supply cord disconnected. Q BAND [DISPLAY] o o o o o o o o o 6 C3 <=> © f Q ® DENON [POWER] BAND > The display switches as shown below each time [DISPLAY] is pressed. ►© STATION NAME : Only displayed when the search mode is set to PRESET and the station name has been registered. I I I r I I ■■ I I 1 I 11 -I © PS : The programme service name and frequency of the station tuned in is displayed. The above is an example for when there is TP data but no RT data. ® PTY : The programme type of the tuned in broadcast is displayed. t -® CT : The current time is displayed. .-.I IT,", Initialization of the microprocessor If the display or operation is abnormal, use the procedure described below to reset the microprocessor. 1 2 Press or [POWER] to set the power to the “standby” mode, then unplug the unit’s power supply cord from the power outlet. While pressing both and BAND, plug the unit’s power supply cord into a power outlet. 3 Check that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 buttons. • The microprocessor will be initialized. • If step 3 does not work, start over from step 1. • When the microprocessor is reset, all the settings are restored to the factory default values. 10 ENGLISH Troubleshootin If a problem occurs, first check the following: 1. Are the connections correct? 2. Is the unit being operated as described in the owner's manual? If this unit does not operate properly, check the items listed in the table below. If the problem persist there may be a malfunction. In this case, disconnect the power immediately and contact the retail outlet. Symptom Cause Measures Page Power does not turn on when ON/STANDBY switch is pressed. • Power supply cord's plug is not plugged in to wall outlet. • Plug the power supply cord in properly. 4 Hissing noise is heard on FM broadcasts. • Antenna cable is not properly connected. • Antenna is not pointing in the right direction. • Radio waves are weak. • Connect the leads properly. • Point the antenna in the right direction. • Install an outdoor antenna. 4 4 4 Hissing or buzzing sound is heard on AM broadcasts. • Noise from a TV or interference in the signals sent from the broadcast station. • Turn off the TV. • Change the position of the loop antenna. • Install an outdoor antenna. 4 4 Booming sound (humming) is heard in AM broadcasts. • Signals transmitted over the power supply cord are modulated by the power source frequency. • Insert the plug in the opposite direction. • Install an outdoor antenna. 4 Nothing happens when remote control buttons are pressed. • Are the batteries dead? • Is the remote control unit too far away? • Is there an obstacle between the remote control unit and the main unit? • You have pressed the wrong button. • Batteries are not set in their proper direction (® and ©). • Replace the batteries with new ones. • Operate from closer to the main unit. • Remove the obstacle. • Press the desired button. • Set the batteries in the proper direction. 2 2 2 3 2 I can not get any sound. • Power connected amplifier not turned on. • Connection leads to amplifier not made correctly. • Turn on the amplifier properly. • Connection leads to amplifier properly. 4 11 ENGLISH Specifications □ FM tuner section (Note: mV at 75 0, • Receiving range: • Antenna terminals: • Usable sensitivity: • S/N 50 dB sensitivity Monaural: Stereo: • Image interference ratio: • IF interference ratio: • AM suppression ratio: • Effective selectivity: • Capture ratio: • Frequency characteristics: • Signal-to-noise ratio Monaural: Stereo: • Total harmonic distortion Mono 1 kHz (at 75 kHz dev.): Stereo 1 kHz (at 67.5 kHz dev.): • Stereo separation 1 kHz (WIDE): 0 dBf=1 x 10-15 W) 87.5 MHz - 108.0 MHz 75 0 Unbalanced 1.0 |jV (11.2 dBf) 1.2 mV (IHF) 1.6 [N (15.3 dBf) 23 |jV (38.5 dBf) 80 dB 100 dB 50 dB 50 dB (±400 kHz) 2.0 dB 20 Hz-15 kHz: +0.5,-1.0 dB 77 dB (IHF), 73 dB (DIN) 72 dB (IHF), 68 dB (DIN) 0.15 % 0.3 % 43 dB □ AM tuner section • Receiving range: • Antenna terminals: • Usable sensitivity: • Signal-to-noise ratio: 522 kHz - 1611 kHz Terminal type with loop antenna 18 [N 53 dB □ Others Power supply: Power consumption: Maximum external dimensions: Mass: AC 230 V, 50 Hz 10W 1 W or less (Standby) 434 (W) x 73 (H) x 286 (D) mm 3.6 kg □ Remote control (RC-1144) Batteries: External dimensions: Mass: 3 V DC, R03/AAA Type (two batteries) 48 (W) x 219 (H) x 22 (D) mm 105 g (including batteries) For purposes of improvement, specifications and design are subject to change without notice. 12 Index nSF" A AM loop antenna..................................................4 Auto preset..........................................................6 Audio cable...........................................
Escreva a sua própria avaliação do dispositivo
|
|
)
