Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
You can remove this protective plastic film from the display. 10 Diverse 4010 Classic ~ Issue 2 ~ 6th Edition ~ 1st March ’02 ~ 4413 Insert the batteries Insert the two batteries supplied, as indicated inside the battery compartment and slide the battery compartment cover shut. The battery cover may be found in the packaging with the batteries. WARNING Under no circumstances should non-rechargeable batteries be used. Only use the approved batteries, please see page 40. Using unapproved batteries will invalidate your guarantee and may damage the telephone. To register your handset, place it in the base station with the display facing upward. After approx. one minute, the handset's internal number is displayed (e.g. INT 1). Successful registration is signalled by a confirmation tone. When the handset is registered the display will show: If the icons on the display flash continuously... It means that the handset is not registered with the base station. Ensure you have correctly carried out step 3 above. If the product has still not registered, please see “Registering manually” on page 37. All additional handsets you purchase will need to be individually registered with the base station before they will work with the Diverse 4010 Classic. Leave the handset for approx. 16 hours in the base station to charge the batteries, as they are not charged in the factory. The battery status icon flashes on the handset to indicate that the batteries are being charged. Helpline If you experience any difficulties with your Diverse 4010 Classic, please call the BT Diverse Helpline on 08457 908 070. SETTING UP Diverse 4010 Classic ~ Issue 2 ~ 6th Edition ~ 1st March ’02 ~ 4413 Battery level icons When the batteries are almost flat a beep sounds and the display shows the empty battery icon. You will need to recharge your handset before you can use it. The various states of charge are shown below: Batteries fully charged Batteries at 66% Batteries at 33% Batteries empty SETTING UP Out of range? If you go out of range of a base station for a long time while your handset is switched ON, it may take more than 20 minutes to ‘find’ the base station again when you come back within range. However, by simply switching the handset OFF for a moment, then ON again, it will find the base station within a few seconds. Battery performance After charging your handset batteries for the first time, subsequent charging time is approximately 4–5 hours. Batteries and case may become warm during charging. This is normal. Under ideal conditions, the handset batteries should give about 10 hours talktime or 200 hours standby time on a single charge. However, new NiCad batteries do not reach their full capacity until they have been in normal use for several days. Fully discharging the batteries at least once a week will help them last as long as possible. However, the charge capacity of rechargeable batteries will reduce with time as they wear out, so reducing the talk/standby time of the handset. Eventually they will need to be replaced. New batteries can be obtained from any BT shop or from the Diverse Helpline 08457 908070. If you replace the handset batteries with ones that have been fully charged, the battery indicator will not show full until the next charge cycle has been completed. Charge the handset until the batteries register full again. From then on the display will be correct. Diverse 4010 Classic ~ Issue 2 ~ 6th Edition ~ 1st March ’02 ~ 4413 4 Connect the telephone line cord to the base and plug into the wall socket Ensure that each end of the line cord is fitted into the correct socket. Fit the belt clip onto the back of the handset. Slot Helpline Your Diverse 4010 Classic is now ready for use. However, If you experience any difficulties please call the BT Diverse Helpline on 08457 908 070. Setting the date and time OK OK OK OK OK MENU Press the MENU options button. Press the DOWN button until the display shows BASE SET. Press the OK button. The display will show AUDIO SET UP. Press the DOWN button until the display shows DATE/TIME. Press the OK button. The display will show DATE SET. Press the OK button. choose AM or PM. Use the keypad to enter the date (DD/MM/YY). Press the OK button. Press the DOWN button until the display shows CLOCK SET. Press the OK button. Use the keypad to enter the time in 12-hour clock format (HH/MM). After entering the time in the 12-hour clock format, press the OK button. Press the DOWN button to SETTING UP Press the OK button. Press the RED PHONE button until you return to the idle screen. Diverse 4010 Classic ~ Issue 2 ~ 6th Edition ~ 1st March ’02 ~ 4413 SETTING UP To set the time mode (12 or 24-hour clock) MENU OK OK OK OK Please note If you subscribe to a Caller Display Service the time and date will be set with the first incoming call. However, the year setting will have to be changed manually, see page 13. The handset’s default setting is 12-hour clock. To change the clock to the 24-hour setting: Press ...