|
Facilidade de uso
• Telephone • Handset • Handset Cord • Line Cord • 3 AA Batteries • Power Adapter • Instruction Manual BATTERY INSTALLATION The 9125 telephone requires 3 AA size 1.5 V batteries for the LCD display. To install the batteries, follow the steps below: 1. Remove the battery cover. The cover is located underneath your phone. 2. Insert 3 AA size 1.5 V batteries. Be careful to observe the polarity markings in the battery compartment. 3. Replace the battery compartment cover. DIALING MODE The 9125 dial mode switch is underneath the phone near the battery compartment. • If your telephone line supports touch-tone dialing, put the switch in the “T” position. This is the default postion from the factory. • If your telephone line requires rotary (Pulse) dialing, put the switch in the “P” position. • If you are unsure which system you have, set the switch to the TONE position. Lift the handset. When you get a dial tone, dial a telephone number. If the dial tone continues, move the switch to PULSE, and then dial the telephone number again. Note: When in PULSE mode, holding the * key for approximately 3 seconds will switch to Tone dialing for the duration of the call. WALL MOUNT 1. The 9125 ships configured for wall mounting. No changes are necessry. 2. Connect the power adapter. The power adapter connects to the jack marked DC 9V on the back of the phone. Plug the large part of the adapter into the wall outlet. Use only a 9V DC. 300mA, center positive Class 2 adapter. The adapter is necessary for LCD backlighting. 3. Connect the line cord. The line cord connects to the jack marked Tel. Line on the back of the phone. 4. Mount the phone on the wall jack. 5. Plug the coiled cord into the handset, and then plug the other end of the cord into the handset jack. 6. Place the handset on the base 9 DESK MOUNT 1. Press in the two areas shown below to release the desk stand. 2. Rotate the desk stand into the desk mounting position as shown below. 3. Connect the power adapter and the line cord. See Steps 2 and 3 in the WALL MOUNT instructions. 4. Plug the coiled cord into the handset, and then plug the other end of the cord into the handset jack. 5. Place the handset on the base. ANSWERING MACHINE 1. Connect the LINE jack of the answering machine to the wall telephone jack. 2. Connect the Tel. Line jack of the 9125 to the PHONE jack of the answering machine. 3. Set the answering machine to answer after 2 or more rings. RINGER VOLUME Set the Ringer Volume Switch to your desired loudness. This switch is on the back of the 9125. Ringer volume can be set to Hi, Low or Off. NOTE: If the ringer volume is set to OFF, it is very easy to miss calls. MODEMS AND FAX MACHINES These devices may be plugged into the Data jack on the back of the 9125. 10 UNIT SETUP Use MENU to enter the setup screen. 1. Press MENU. PHONE BOOK appears on the display. The Phone Book is covered in a later section. 2. Press . When CALL WAITING appears, press ENTER. Then use to toggle this feature ON or OFF. If this is set to OFF, Caller ID information will not be displayed for a Call Waiting call. Press ENTER to exit. 3. Press . When DATE FORMAT appears, press ENTER. Then use to select either Month-Day (MM-DD) and Day-Month (DD-MM). Press ENTER to exit. 4. Press . When HOUR FORMAT appears, press ENTER. Then use to select either 12 hour or 24 hour time display. Press ENTER to exit. 5. Press . When SET FLASH appears, press to select between 600ms, 300 ms, 120 ms and 100ms. Press ENTER to exit. 6. Press . When SET AREA CODE appears, use the keypad to enter the area code in which the phone will be used. This is necessary so that the # key can change dialing formats (7 digits, 10 digits, 11digits). 7. Press . When SET LANGUAGE appears, press to select between USA-UK (English), FRENCH and SPANISH. Press ENTER to exit. Note that pressing ENTER now returns the phone to the idle screen. NOTE: If you have Caller ID service, the time will be automatically set. Use Step 8 only if you do not have Caller ID. If you wish to display the Day of the Week, you will need to set the year since Caller ID does not include this. 8. Press MENU. Then press or until SET TIME appears. Press ENTER to set the time. a. The “tens” digit in the hour is flashing. Use or to set this digit. Then press ENTER. b. The “ones” digit in the hour is flashing. Use or to set this digit. Then press ENTER. c. The “tens” digit in the minute is flashing. Use or to set this digit. Then press ENTER. d. The “ones” digit in the minute is flashing. Use or to set this digit. Then press ENTER. e. The “tens” digit in the month is flashing. Use or to set this digit. Then press ENTER. f. The “ones” digit in the month is flashing. Use or to set this digit. Then press ENTER. g. The “tens” digit in the day is flashing. Use or to set this digit. Then press ENTER. h. The “ones” digit in the day is flashing. Use or to set this digit. Then press ENTER. i. The “tens” digit in the year is flashing. Use or to set this digit. Then press E...
Este manual também é adequado para os modelos :Telefones sem fio - Caller ID Type II 9125 (174.11 kb)
Telefones sem fio - Caller ID Type II 9125 (174.11 kb)
Telefones sem fio - Caller ID Type II 9125 (174.11 kb)
Telefones sem fio - Caller ID Type II 9125 (174.11 kb)