Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
21) IN USE/CHARGE Indicator (p. 14) 8 Handset Display The handset shows you information and instructions on the display. These display prompts are shown below. No items stored The Caller List for both lines is empty. Recharge A // A_i]v _Í_Ä- 12 new calls (III] 12 new calls v=New A=01d 'Ringer off Talk 01-06-35 {M|] Out of range Save error TINA ROBINSON 1-000-222-3333Ü The battery needs to be charged. Place the handset on the base unit to charge the battery (p. 14). The display shows the number of new calls for both lines and the battery strength (p. 14) while the handset is on the base unit. This display will be shown when: — you lift the handset off the base unit, or — SEARCH 0 or 0 is pressed when the handset is off the base unit. To search from the most recent call, press SEARCH Q (New key). To search from the oldest call, press SEARCH 0 (old key) (p. 30). When the handset ringer volume is set to OFF for both lines (p. 21), “Ringer off” will flash for about 45 seconds before the handset returns to the stand-by mode (p. 15). During a conversation, the display shows the length of the call (ex. 1 hour, 6 minutes and 35 seconds). The battery strength is also displayed. The handset has lost communication with the base unit. Move closer to the base unit. While programming, the handset lost communication with the base unit. Move closer to the base unit. When a call is received, the display shows the caller’s name, number and the called line after the first ring. 9 Preparation JACK SMITH 111-2222 fl 11 :20A JAN12 X3 Paging This is a name from the Caller List. The display shows: — the caller’s name, — the caller’s number and the called line, — the time and date of the last call (ex. Jan. 12, 11:20 AM), and — the number of times called (ex. 3 times). The base unit is paging the handset (p. 42). Hold 00-01-12 (III] NANCY BROWN 1-000-222-333 3Q ----Waiting---- An outside call has been put on hold by the handset user. To release the hold, press the line button whose indicator is flashing (p. 23). A second call is received during a conversation (p. 44). Please lift up and try again SEARCH @ or © was pressed while the handset was on the base unit. Lift the handset and press SEARCH @ or 0 again. 10 Settings Connecting the AC Adaptor • USE ONLY WITH Panasonic AC ADAPTOR PQLV1 (Order No. PQLV1Z). • The AC adaptor must remain connected at all times, (It is normal for the adaptor to feel warm during use.) • To connect a standard telephone on the same line, see page 49. • If your unit is connected to a PBX which does not support Caller ID and voice mail services, you cannot access those services. 11 Preparation ^ Settings Connecting the Telephone Line Cord Connect the telephone line cord(s) to the unit as follows. I To connect a two-line telephone jack 12 To connect two single-line telephone jacks 4-Wire Telephone Line Cord with GREEN Plugs LINE 2 Single-Line Telephone Jacks (RJ11C) 2-Wire Telephone Line Cord with TRANSPARENT Plugs PH* LINE 1 If you use the unit as a single-line telephone only Single-Line Telephone Jack (RJ11C) 2-Wire Telephone Line Cord with TRANSPARENT Plugs LINE 1 You can only use LINE 1 with this connection. 13 Preparation ^ Settings Battery Charge Place the handset on the base unit and charge for about 4 hours before initial use. • The IN USE/CHARGE indicator lights. Battery strength You can check the battery strength on the display while the handset is on the base unit, while it is in use (making/answering a call etc.), or after viewing the Caller List, programming, etc. The battery strength will remain for 5 seconds after using the handset, then the display will return to the stand-by mode (see next page). The battery strength is shown as in the chart below. Display prompt Battery strength {ini Fully charged { in Medium { i] Low I]* (flashing) ❖ ^ Needs to be recharged. Recharge Recharge the battery when: — “Recharge” is displayed, — “ { l ] ” flashes on the display, or — the handset beeps intermittently while it is in use. • If you DO NOT recharge the handset battery for more than 15 minutes, the display will keep indicating “Recharge” and/or “i ■ ] ” will continue to flash. Recharge !( it 14 Battery information After your Panasonic battery is fully charged (p. 14): Operation Approx. battery life While in use (TALK) Up to about 8 hours While not in use (Stand-By) Up to about 21 days • Battery life may be shortened depending on usage conditions, such as viewing the Caller ID Caller List, and ambient temperature. • Clean the handset and the base unit charge contacts with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the battery may not charge properly. • If the battery is fully charged, you do not have to place the handset on the base unit until “Recharge” is displayed and/or “( 11" flashes. This will maximize the battery life...