Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
Reprogram if necessary. 10 Selecting the Ringer Volume With the handset The TALK indicator light must be oft. • To select HIGH (preset) or LOW, press I RINGER I briefly. (Each time you press the button briefly, the selected volume rings and the ringer volume will change.) • To turn the ringer OFF, press and hold I RINGER I until 2 beeps sound. • To turn the ringer ON, press I RINGER I briefly. The ringer sounds at the HIGH level. With the base unit Set the RINGER selector to HIGH, LOW, or OFF. • When set to OFF, the base unit will not ring. Selecting the Handset Ringer Tone (2 Types) The TALK indicator light must be off. ■j Press IrTngerI. 2 Press (*) within 5 seconds. • The selected ringer tone sounds. • Each time you press (*] within 5 seconds, the ringer tone will change. Making Calls With the Handset 1 Press I TALK I. • The TALK indicator lights. O Dial a telephone number. • If you misdial, press I FLASH I firmly then dial again. To hang up, press I TALK) or place the handset on the base unit. • The TALK indicator light goes out. I TALK I and Indicator • If an alarm tone sounds in step 1, move closer to the base unit or place the handset on the base unit. Then try again. • To switch to the speakerphone during a call with the handset, see page 18. To redial the last number dialed on the handset Press I TALK I + iREDIALl. To select the receiver volume Press I LOUD I while talking. • Each time you press the button, the volume level will change from MEDIUM (preset) to HIGH to LOW. 12 If noise interferes with the conversation Press |CHl to select a clearer channel or move closer to the base unit. To put a call on hold Press (hold]. • The TALK indicator and the SP-PHONE indicator flash simultaneously. • After 6 minutes, warning tones will sound every about 16 seconds. After a total of 10 minutes, the call will be disconnected. To release the hold For the handset, press ITALKI. For the base unit, press I SP-PHONE I. • If another phone is connected on the same line (p. 27), you can also release the hold by lifting its handset. Lighted keypad The dialing buttons will light while dialing and flash when a call is received. The lights will go out about 10 seconds after dialing or answering the call. ^ Making Calls With the Base Unit -| Press [SP-PHONE I. • The indicator lights. 2 Dial a telephone number. • If you misdial, press I FLASH I firmly then dial again. When the other party answers, talk into the MIC (microphone). To hang up, press I SP-PHONE]. • The SP-PHONE indicator light goes out. VOLUME [V], fÂl I FLASH] REDIAL/PAUSE 1 SP-PHONE ] and Indicator HOLD) MIC • For best speakerphone performance, use in a quiet room and speak alternately with the caller. • If the other party has difficulty hearing you, press VOLUME [v] to decrease the speaker volume. Decreasing the speakerphone volume will increase the microphone sensitivity. • While using the speakerphone, if the handset is on the base unit, you may switch to the handset by lifting it up. To adjust the speaker volume (12 levels) while talking To increase, press VOLUME (/\). To decrease, press VOLUME [v]. To redial the last number dialed on the base unit Press I SP-PHONE I * [ REDIAL/PAUSE I. 14 To put a call on hold Press [HQLDl. • The SP-PHONE indicator flashes. • After 6 minutes, warning tones will sound every about 16 seconds. After a total of 10 minutes, the call will be disconnected. To release the hold For the base unit, press I SP-PHONE I. For the handset, press [ TALK I or lift the handset off the base unit. • You may also press I REMOTE SPl on the handset to release the hold at the base unit. • If another phone is connected on the same line (p. 27), you can also release the hold by lifting its handset. ^ Making Calls Simultaneous Keypad Dialing You can use the base unit like a standard telephone. After pressing I TALK) to make a call with the handset near the base unit, you can also dial using the base unit keypad. 1 2 Handset: Press [TALK] Base unit: Dial a telephone number while hearing a dial tone with the handset. • When the other party answers, talk using the handset. Handset: To hang up, press I TALK I or place the handset on the base unit. Useful information You can enter numbers using the base unit keypad during a call with the handset. For example, to access an answering service, electronic banking service, etc. 1. Handset: Press ¡TALKI. 2. Handset: Dial a telephone number. • You may also dial with the base unit keypad. 3. Base unit: Enter the required numbers while listening to the pre-recorded instrucions. 4. Handset: To hang up, press I TALK I or place the handset on the base unit. Simultaneous Keypad Dialing is available only after pressing I REMOTE SPl {p. 19) or I TALK I. 16 Answering Calls With the Handset If the handset is off the base unit, press I TALK I. • You can also answer a call by pressing any dialing button ...