Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
To connect a standard telephone on the same line, use the Panasonic T-adaptor KX-J66. To order, call 1-800-332-5368. 48 Before Requesting Help Cordless Telephone Problem Remedy An alarm tone sounds when you press (TALK), (SCREEN/PLAYBACK) or (INTERCOM]. •You are too far from the base unit. Move closer and try again. • Place the handset on the base unit and try again. • Plug in the AC adaptor. • Raise the base unit antenna. Static, sound cuts in/out, fades. Interference from other electrical units. ► Locate the handset and the base unit away from other electrical appliances (P- 3). ► Move closer to the base unit. ► Raise the base unit antenna. ► Press (CH) to select a clearer channel. The handset does not ring. ►The ringer volume is set to OFF. Press (RINGER) briefly while the TALK indicator light is off {p. 13). You cannot store a phone number in memory. •You cannot store a number while the unit is in the talk, hold or intercom mode. • Do not pause for over 30 seconds while storing. While storing a phone number, the unit starts to ring. ►To answer the call, press (TALK). The program will be canceled. Store the number again. [LOCATOR/INTERCOM does not function. •The handset is too far from the base unit or is engaged in an outside call. r 49 Before Requesting Help Answering System Problem Remedy The answering system is on, «The recording time is set to “greeting but incoming messages are only”. Select “1 minute” or "unlimited” not recorded. (p. 18). • Memory is full. Erase some or all of the messages (p. 32). “ nun ” is displayed and the ANSWER ON indicator flashes rapidly, and no new messages are recorded. • Memory is full. Erase some or all of the messages (p. 32). If11 EOT!” is still displayed and the ANSWER ON indicator flashes rapidly, erase your greeting message and re-record a shorter greeting (p. 14, 15). Some incoming messages have not been recorded completely. •Set the CPC function to “b” (p. 20). You cannot operate the answering system at the base unit. •The handset user is operating the answering system. Wait until the IN USE/CHARGE indicator light goes out. You cannot operate the • Be sure to enter the correct remote answering system from a code. touch tone phone. •The answering system may not respond if the tones are too short to activate the unit. Press each button firmly. •The answering system is off. Turn it on (p. 41). You cannot operate the answering system with the handset by pressing (SCREEN/PLAYBACK). •Someone is operating the answering system. •You are too far from the base unit. Move closer to the base unit. 50 General Problem Remedy The unit does not work. • Check the settings (p. 10-13). •Charge the battery fully (p. 11). •Clean the charge contacts and charge again (p. 11). • Install the battery properly (p. 47). •Place the handset on the base unit and unplug the AC adaptor to reset. Plug in, then try again. • Re-insert the handset battery within 5 minutes to avoid memory loss and place the handset on the base unit. Then try again. You cannot program items • Programming is not available while the such as the time/day unit is in the talk, hold or intercom adjustment (p. 17). mode. • Move closer to the base unit. The RECHARGE indicator flashes or the unit beeps intermittently. •Charge the battery fully (p. 11). You charged the battery fully, • Clean the charge contacts and charge but the RECHARGE indicator again (p. 11). flashes. • Install a new battery (p. 47). The IN USE/CHARGE indicator light never goes out while charging. •This is normal. If you cannot solve your •Call our customer call center at problem. 1 -800-211 -PAN A(7262). V. 51 Important Safety Instructions When using this unit, basic safety precautions should always be followed to reduce the risk of fire, electric shock, or personal injury. 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on this unit. 3. Unplug this unit from AC outlets before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this unit near water, for example, near a bathtub, washbowl, kitchen sink, or the like. 5. Place this unit securely on a stable surface. Serious damage and/or injury may result if the unit falls. 6. Do not cover slots and openings on the unit. They are provided for ventilation and protection against overheating. Never place the unit near radiators, or in a place where proper ventilation is not provided. 7. Use only the power source marked on the unit. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. 8. Do not place objects on the power cord. Install the unit where no one can step or trip on the cord. 9. Do not overload wall outlets and extension cords. This can result in the risk of fire or electric shock. 10. Never push any objects through slots in this unit. This may result in the risk of fire or electric shock. ...