Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
To attach the belt clip To remove the belt clip 1-E Wall Mounting This unit can be mounted on a wall phone plate. 1 1 Adjust the angle of the cradle: #Slide the lock switch to “RELEASE”. $Rotate the cradle 90° until it faces straight up. %Slide the lock switch to “LOCK” with the cradle facing straight up. 2 1 3 Back Side Back Side 2 2 Connect the AC adaptor. To Power Outlet 3 3 #Tuck the telephone line cord inside the wall mounting adaptor. $Connect the telephone line cord to the unit. %Install the adaptor by pushing it in the direction of the arrow. •The word “UP” should face upward. 1 2 3 4 4 Connect the telephone line cord. Mount the unit, then slide down. •Raise the antennas. Section 2Making/Answering Calls2 2-A Making Calls 1 1 Press (TALK). •The TALK indicator lights. •If an alarm tone sounds, see 6-F. 2 2 Dial a phone number. TALK Indicator 3 3 To hang up, press (TALK) or place , the handset on the base unit. (TALK) (REDIAL) (CH) 2-B Answering Calls If the handset is off the base unit, press (TALK). •You can also answer a call by pressing any dialing button (0) to (9), (*) or (#) (— Any Key Talk). OR If on the base unit, just lift up. To redial the last number dialed Press (TALK) \ (REDIAL). To select the receiver volume 3 levels (HIGH, MEDIUM, LOW) are available. Press N or O while talking. •Each time you press N or O, the volume level will change. If noise interferes with the conversation Press (CH) to select a clearer channel or move closer to the base unit. Selecting the ringer volume The TALK indicator light must be off. •To select HIGH (preset) or LOW, press N or O. Each time you press N or O, the ringer volume will change and the selected volume will ring. •To turn the ringer OFF, press and hold O until 2 beeps sound. •To turn the ringer ON, press N. The ringer will sound at the HIGH level. •When you replace the battery, the selected ringer volume setting will return to the factory set. • For best operating performance, see section 6-D. Lighted handset keypad The handset dialing buttons will light when you press a button or lift the handset off the base unit, and flash when a call is received. The lights will go out a few seconds after pressing a button, lifting the handset or answering a call. Speed Dialer Section 33 3-A Storing Phone Numbers in Memory You can store up to 10 phone numbers in the handset. The dialing buttons ((0) to (9)) function as memory stations. (PAUSE) TALK Indicator (TALK) AUTO Memory Station Numbers PROGRAM 1 1 The TALK indicator light must be off before programming. Press PROGRAM a. 2 2 •The TALK indicator flashes. Enter a phone number up to 22 digits. 4 4 3 3 Press AUTO U. Press a memory station number ((0) to (9)). •A beep sounds. •To store other numbers, repeat steps 1 through 4. If you misdial Press PROGRAM a to end storing. \ \ Start again from step 1. To erase a stored number Press PROGRAM a \ AUTO U \ \ the memory station number ((0) to (9)) for the phone number to be erased. •A beep sounds. •If a pause is required for dialing, press (PAUSE) where needed. Pressing (PAUSE) counts as one digit (5-D). 3-B Dialing a Stored Number Press (TALK) \ AUTO U \ the memory station number ((0) to (9)). •If your line has rotary or pulse service, any access numbers stored after pressing (TONE) will not be dialed. Special Features5 5-A For Call Waiting Service Users Press (FLASH) if you hear a call-waiting tone while talking. •The first call is put on hold and you can answer the second call. •To return to the first caller, press (FLASH) again. •If this function does not operate properly, consult your telephone company for details. 5-B Automatic Security Code Setting Whenever you place the handset on the base unit, the unit automatically selects one of more than a million security codes. These codes help prevent the unauthorized use of your telephone line by another cordless telephone user. 5-C Temporary Tone Dialing (For Rotary or Pulse Service Users) Press (TONE) before entering access numbers which require tone dialing. •The dialing mode changes to tone. You can enter numbers to access an answering service, electronic banking service, etc. When you hang up, the mode will return to pulse. •Access numbers entered after pressing (TONE) will not be included when redialing. 5-D How to use the PAUSE Button (For Analog PBX Line/Long Distance Service Users) We recommend you press (PAUSE) if a pause is required for dialing with a PBX or to access a long distance service. Ex: Line access number (9) (PBX) (9) \ (PAUSE) \ Phone number •Pressing (PAUSE) once creates a 3.5 second pause. This prevents misdialing when you redial or dial a stored number. •Pressing (PAUSE) more than once increases the length of the pause between numbers. 5-E Handset Locator You can locate the handset or page the handset user with beep tones. 1 1 Press (HANDSETOLOCATOR) on the base unit. •The IN USE/CHARGE indicator flashes and the handset beeps for 1 minute. 2 2 To stop paging, press (HANDSETOLOCATOR) again or ...