Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Pressing both S2 and S3 buttons simultaneously for about a second, the microphone will be muted. A periodic beep tone will be heard while the mute function is active. When the microphone is muted, press on both S2 and S3 buttons simultaneously will end the mute function and the periodic beep tone will stop. While a call is in session on the Headset pressing S1 will disconnect the call. After the call is disconnected, the status light will flash every 3 seconds To reject a call (this function will only be supported by some mobile phones, e.g. Nokia 3650 or Siemens S55) When the Headset rings, press and hold S1 until you hear a long beep tone. 1.Make sure the voice dialing function is enabled in the mobile phone and the mobile phone is within the range of the Headset. Press S1 on the Headset shortly. 2.After you hear the beep tone in the Headset, make a voice dial as you normally would by saying the name of the contact as set up in the memory of the mobile phone. The call will be connected in a few seconds. (this function will only be supported by some mobile phones, e.g. Nokia 3650 or Siemens S55) To redial the last dialed number, press and hold S3 for 2 seconds. short low tones will indicate an attempt to redial. Bluetooth Bluetooth Bluetooth Bluetooth To mute the microphone during an active call To end the mute function Requires a Bluetooth mobile phone with Voice Dialing function Right or left ear If you want to wear the Headset on your right ear, you have to change the orientation of the ear hook. 2) Put the ear hook back to the knuckle joint and pull it down firmly. 1) Pull the ear hook upward from the knuckle joint and flip the hook 180 degrees. Left ear orientation Right ear orientation Bluetooth Headset VOX 120 User Manual Adjusting Speaker Volume . . , . While a call is in session, repeatedly pressing and releasing S2 will increase the speaker volume and repeatedly pressing and releasing S3 will decrease the speaker volume on the Headset There is a key tone to indicate volume increase or decrease However a warning tone will be heard when the volume level reaches its maximum or minimum Health and safety Do not allow the product to come into contact with liquid. Do not open it. 1. Philips Royal Electronics manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive electro magnetic signals. 2. One of Philips' leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products. 3. Philips is committed to develop, produce and market products that cause no adverse health effects. 4. Philips confirms that if its products are handled properly for their intended use, they are safe to use according to scientific evidence available today. 5. Philips plays an active role in the development of international EMF and safety standards, enabling Philips to anticipate further developments in standardization for early integration in its products. The Declaration of conformity is available on On line help: Electric, Magnetic and Electromagnetic Fields ("EMF") Conformity Maintenance and service 1. Marche/Arret (S1) 2. Volume + (S2) 3. Volume - (S3) 4. Diode d'etat 5. Prise CC 6. Haut-parleur 7. Joint de charniere 8. Microphone 9. Contour d'oreille Charger la batterie Allumer le casque Eteindre le casque Mettre le casque en mode couplage Nous vous remercions d'avoir choisi le nouveau casque VOX 120 . Avant la premiere utilisation, il est important de charger la batterie pendant une duree de 12 heures. Pendant que le casque est hors tension, appuyez sur S1 pendant 2 secondes. Un signal grave suivi d'un signal aigu indiquera que le casque est maintenant sous tension. La diode d'etat verte clignotera pendant une seconde. Puis la diode d'etat verte continuera a clignoter toutes les 3 secondes. Pendant que le casque est sous tension, appuyez sur S1 pendant 5 secondes. Un signal aigu suivi d'un signal grave indiquera que le casque est maintenant hors tension. Et la diode d'etat sera rouge jusqu'a ce que vous relachiez S1. Assurez-vous que le casque est totalement charge et que le cable de chargement est deconnecte avant de demarrer le couplage. Pendant que le casque est hors tension, appuyez sur S1 pendant 4 secondes. la diode d'etat clignotera rouge et vert alternativement, indiquant que le casque est en mode couplage. Referez-vous au mode d'emploi de votre telephone portable pour demarrer la procedure de couplage. Habituellement, ceci doit etre effectue en se rendant dans un menu d'installation ou de connexion puis en selectionnant les options pour detecter les dispositifs . peut avoir besoin de quelques secondes avant d'etablir une connexion. L'ecran de votre telephone indiquera qu'il a trouve le casque "VOX 120" et vous dema...