Assessments - 0, GPA: 0 ( )

Fabricante : Philips Arquivo Tamanho: 938.39 kb Arquivo Nome : Língua de Ensino:

••The type plate is located on the bottom of the base station. 1 Connect each end of the power adapter to: • the DC input jack at the bottom of the base station; • the power socket on the wall. 2 Connect each end of the line cord to: • the telephone socket at the bottom of the base station; • the telephone socket on the wall. 3 Connect each end of the power adapter to (for multi handset version only): • the DC input jack at the bottom of the extra handset charger. • the power socket on the wall. Install the handset The batteries are pre-installed in the handset. Pull the battery tape off from the battery door before charging. EN Caution ••Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard batteries in fire. ••Use only the supplied batteries. ••Risk of decreased battery life! Never mix different brands or types of batteries. Note ••Charge the batteries for 8 hours before first use. ••If the handset becomes warm when the batteries are being charged, it is normal. Warning ••Check the battery polarity when inserting in the battery compartment. Incorrect polarity may damage the product. The batteries are pre-installed in the handset. Pull the battery tape off from the battery door before charging. Configure your phone (country dependent) 1 When using your phone for the first time, you see a welcome message. 2 Press MENU/OK. Set the country/language Select your country/language, then press MENU/OK to confirm. »»The country/language setting is saved. Note ••The country/language setting option is country dependent. If no welcome message is displayed, it means the country/language setting is preset for your country. Then you can set the date and time. To re-set the language, see the following steps. 1 Select [MENU] > [PHONE SETUP] > [LANGUAGE], then press MENU/OK to confirm. 2 Select a language, then press MENU/OK to confirm. »»The setting is saved. Set the date and time Tip ••To set the date and time later, press REDIAL/C to skip this setting. 1 Press MENU/OK. 2 Select [PHONE SETUP] > [DATE/TIME], then press MENU/OK to confirm. 3 Press the numeric buttons to enter the date, then press MENU/OK to confirm. »»The time setting menu is displayed on the handset. 4 Press the numeric buttons to enter the time. • If the time is in 12-hour format, press / to select [AM] or [PM]. 5 Press MENU/OK to confirm. Change the remote access PIN code Note ••The default answering machine remote access PIN code is 0000 and it is important to change it to ensure the security. EN 1 Press MENU/OK. 2 Select [ANSW MACHINE] > [REMOTE ACC.] > [CHANGE PIN], then press MENU/OK to confirm. 3 Enter the old PIN, then press MENU/OK to confirm. 4 Enter the new PIN code, then press MENU/OK to confirm. 5 Enter the new PIN code again, then press MENU/OK to confirm. »»The setting is saved. Charge the handset Place the handset on the base station to charge the handset. When the handset is placed correctly on the base station, you hear a docking sound. »»The handset starts charging. Note ••Charge the batteries for 8 hours before first use. ••If the handset becomes warm when the batteries are being charged, it is normal. You can activate or deactivate the docking tone (see 'Set the docking tone' on page 20). Your phone is now ready to use. Check the battery level The battery icon displays the current battery level. When the handset is off the base station/charger, the bars indicate the battery level (full, medium and low). When the handset is on the base station/charger, the bars flash until charging completes. The empty battery icon flashes. The battery is low and needs recharging. The handset turns off if the batteries are empty. If you are on the phone, you hear warning tones when the batteries are almost empty. The call gets disconnected after the warning. What is standby mode? Your phone is in standby mode when it is idle. The standby screen displays the handset name or date and time, and handset number. Tip ••Press and hold MENU/OK to switch between the handset name and date and time display. EN Check the signal strength The number of bars indicates the link status between the handset and base station. The more bars are shown, the better the connection is. • Make sure the handset is linked to the base station before you make or receive calls and carry out the phone functions and features. • If you hear warning tones when you are on the phone, the handset is almost out of battery or the handset is out of range. Charge the battery or move the handset nearer to the base station. Switch the handset on or off Press and hold to switch the handset on or off. EN 4 Calls Note ••When the power fails, the phone cannot access emergency services. Tip ••Check the signal strength before you make a call or when you are in a call (see 'Check the signal strength' on page 10). Make a call You can make a call in these ways: • Quick call • Dial before you call • Redial the most recent number • Call from the redial list. • Call from the phoneb...

Baixe o seu

Para fazer o download, introduza 2 dígitos :