Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
• 1 base station equipped with a loudspeaker. • 1 power supply block which provides the base with electrical power. • 1 telephone cable. • 1 user’s manual. Your telephone’s operating capacity Your telephone works from a battery located inside the handset. • Battery charging starts as soon as you place the handset on its base. A completely discharged handset will take about 24 hours to charge. • With a fully charged new battery, your handset will be able to operate for about 8 hours on-line and about 8 days on stand-by (in other words when not communicating). • To recharge your telephone, the base must be connected to a power supply. Only use the mains adaptor supplied with your phone. Note: You can place your handset on the base station with the keypad face up or face down. Protecting your telephone Fraudulent use of your telephone line by another cordless phone is unlikely as the base station assigns the handset one of a possible 65,535 identification codes. This code means that only your handset is authorised to use your line for making calls. In the event of a power failure In the event of a power failure, your Icana 5350 cordless telephone will lose: • the Redial memory. • any unconfirmed number in course of memorisation. But will save: • the numbers in your phonebook. • the caller list. 3 Helpful hint To ensure maximum handset charge, replace the handset on the base station regularly. 4 Setting up your Icana 5350 1 On the top side of the base station, connect the telephone cable to the smaller of the sockets and then to the telephone socket in the wall. 2 Connect the power supply cable to the larger of the sockets on the base station and then to the power outlet. The indicator light on the base station lights up. Your telephone is now correctly connected. 3 Fully extend the base station antenna. 4 Place the handset on its base station and leave it to charge for at least 15 minutes. Your telephone is now ready to make or receive calls in “Tone dialling” mode*. To charge the battery completely, leave the handset on its base station for 24 hours. Mains power supply Telephone line 6 Changing the dial mode Your telephone has two possible dial modes: "tone" or "pulse". The factory setting for your telephone is "tone"*. If you are not connected to an electronic central exchange, you need to use "pulse". To set the dial mode from “tone” to “pulse”: 1 Pick up the handset and press ®. The indicator light on handset and base station starts flashing. 2 Press the key. 3 Press the key. Your handset emits 3 beeps to confirm. The telephone is now ready to dial in "pulse" mode. To set the dial mode from "pulse" to "tone": 1 Pick up the handset and press ®. The indicator light on handset and base station starts flashing. 2 Press the key. 3 Press the key. Your handset emits 3 beeps to confirm. The telephone is now ready to dial in "tone" mode. * When your telephone line is connected to an electronic exchange, the "tone" mode provides faster dialling, and access to special telephone network services. Loop Disconnect Signalling: Although this equipment can use either loop disconnect or DTMF signalling (Tone dialling), only the performance of the DTMF signalling (Tone dialling) is subject to regulatory requirements for correct operation. It is therefore strongly recommended that this equipment is set to use DTMF signalling (Tone dialling) for access to public or private emergency services. DTMF signalling (Tone dialling) also provides faster call set up. 5 7 8 loudspeaker key telescopic antenna phonebook key manual channel strip key talk key phoneline indicator light earpiece LCD display caller list key SOS key microphone recall (for use with Network services or attached to a PABX) and programming key redial key base station loudspeaker base station antenna phoneline / power indicator light Copyright © Philips 1998 - All rights reserved. mains power supply cable telephone cable dialling keypad Thank you for purchasing a Philips Icana 5350 cordless telephone Your Icana 5350 cordless telephone incorporates advanced Philips cordless technology for even greater simplicity and user-friendliness. Your Icana 5350 is fitted with a multi-channel radio system, which allows you to avoid interference during calls using the D2NS system (Dual Dynamic Noise Suppressor) to eliminate hiss. Your Icana 5350 is fitted with a liquid crystal display screen on the handset, giving you all the features of a real phonebook - 25 names and telephone numbers. You can also identify the telephone number of the caller (Caller ID)* and consult the Caller ID list*. Lastly, you can see how long your calls last. This instruction manual will help you discover your product’s features and get to know its wide range of functions. SAFETY INFORMATION: The only way to cut off the power supply to the telephone is to disconnect the power supply block from the mains outlet. Be sure that the mains outlet is located near the telephone and is easily accessible. Important!...
Este manual também é adequado para os modelos :Telefones sem fio - TD5350 (2.22 mb)