Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
Please retain for future reference. 2 EXPLODED PARTS VIEW 13 14 14 13 Fig.2 12 11 10 9 7 8 4 5 6 2 3 1 A B Fig.1 Fig.3 HV3500 HV2900/ 3900 PARTS LIST FFiigg..11 No.Description Part Code No.Description Part Code 1. Needle and Fluid Tip Tool V0018 7. Fluid Needle 2.0mm V0006 2. Air Cap Ring V0001 8. Lip Seal -Fluid Needle V0007 3. Air Cap V0002 9. Paint Flow Adjuster V0011 4. Spray Direction Plate V0003 10. Paint Container Seal L0682 5. Fluid Tip 2.0mm V0004 11. Pick-up Tube V0012 6. Fluid Tip O-Ring V0005 12. Paint Container V0014 PARTS LIST HV3500 Fig.2 No.Description Part Code 13. Hose L1064 14. Filter L0290 PARTS LIST HV2900/3900 Fig.3 No.Description Part Code 13. Hose L0896 14. Filter L0290 SAFETY OPERATING INSTRUCTIONS PLEASE READ BEFORE USE • Never under any circumstances aim the Spray Gun at another person or animal. In the event of injury occurring seek expert medical advice immediately. • The Spray Gun must only be used with paints and solvents that have a flash point suitable for spraying. If in doubt, consult the paint or solvent manufacturer s data. • Always ensure there is adequate ventilation when spraying. • NEVER spray near a naked flame, including appliance pilot light. • NEVER smoke whilst spraying. • NEVER allow children to operate or play with the Spray Gun. • Always read the solvent manufacturer s instructions before use. • Always disconnect unit from mains supply when filling the paint container. • Always wear a suitable protective mask when spraying. We would also recommend the use of gloves, goggles and overalls. • After each use, thoroughly clean the Spray Gun. • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. • Use only genuine manufacturer replacement parts. • Always disconnect the Spray Station from the mains supply before cleaning the appliance. • Warning: The use of any accessory or attachment, other than those recommended in this instruction manual, may present a risk of personal injury. • Use the Spray Gun for the job it was designed for only. Mis-use of the Spray Gun will invalidate the guarantee. • Wear ear protection. WARNING: The substances used with this Spray Gun (paints, solvents, etc.) may contain dangerous, harmful, explosive or corrosive materials. ALWAYS COMPLY WITH THE SAFETY INSTRUCTIONS ISSUED WITH THIS PRODUCT AND THE MATERIAL BEING USED. INTRODUCTION The concept A motor feeds out a high volume of air (HV) and enables products to be sprayed at a low pressure (LP). The Hose feeds the air produced by the motor to the Spray Gun. The solution is released from the Fluid Tip of the Spray Gun at a very low pressure and is enclosed in a high volume of air. The powerful motor can spray a wide range of solutions with or without dilution. However, there will always be some which will not be suitable for the Spray Gun. Good quality paint contains a high percentage of solids which make the dilution easier. The users must keep in mind that low temperatures make the paint thicker, that s why we recommend spraying with the Spray Gun at a 15°C minimum temperature. 3 SET UP • Fill the Paint Container (12) with the product to be sprayed. Stir well (as mentioned previously) and strain to remove any bits which will interfere with a smooth consistent spray. • Make sure the Paint Container Seal (10) and Pick-up Tube (11) are firmly fitted into the base of the Spray Gun. • Screw the Paint Container (12) to the base of the Spray Gun and tighten accordingly. • Start with the Paint Flow Adjuster (9) at its minimum setting so the Trigger can not be pulled. Do not forget that the Paint Flow Adjuster controls the quantity of paint sprayed (Fig.4). • Uncoil the air Hose and attach it to the back of the Spray Gun and the other end to the Spray Station. • Uncoil the power cable and attach the plug to the mains supply. • Switch the Spray Station on. This will immediately cause some air to be produced, which is quite NORMAL. However, none of the product will be sprayed until the Spray Gun Trigger is pulled. • Very important: when spraying for the first time, we recommend that you always leave the motor unit to run for 1 to 2 minutes before applying the product. Do not forget that the Paint Flow Adjuster controls the quantity of paint sprayed (Fig.5). ALWAYS MAKE SURE THAT THE MOTOR UNIT IS ON A RIGID SURFACE AND FREE FROM DUST. 4 SPRAYING HORIZONTAL ROUND VERTICAL 3 Spray Patterns Horizontal and Vertical Spray with varying widths Round Spray Vertical and Horizontal for normal sized jobs Round for small and precise jobs Fig.6 Fig.7 Fig.5 PREPARATION • Carefully cover areas which are not to be painted with a plastic cover and protective tape. • Wear a suitable mask when spraying products (and make sure there is adequate ventilation in the room when working in...
Este manual também é adequado para os modelos :Armas - HV2900 (2.78 mb)
Armas - HV3900 (2.78 mb)