Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
2. Pour any residual material into its container so that it can be used for the future. 3. Pour a quantity of the respective thinner into Container, shake the gun lightly, reassemble the gun, then spray this liquid through the gun. Repeat this until the thinner being sprayed is coming through with no traces of paint. 4. Clean any traces of paint off the outside of the gun. 5. Clean the Paint Container Seal (12) inside the gun body. 7 L0553 (04-08) (US-FR-ES).qxd 20/6/08 2:25 pm Page 8 L0553 (04-08) (US-FR-ES).qxd 20/6/08 2:25 pm Page 8 1. NOZZLE & NEEDLE Unscrew Air Cap (1). 2. Remove the Air Cap (2). 3. Completely remove Fluid Adjustment Screw (8). 4. Remove the Spring (7). 5. Push out the Needle (6) – do not use tools for this. 6. Remove the Fluid Tip (4). 7. Remove Fluid Tip Seal (5). 8. Remove Spray Direction Plate(3). 9. Place all of these items into a container and clean them using a brush and clean thinners. 10. Clean the inside of the gun. 11. Thoroughly dry these parts before reassembling. 12. Grease the Gland Seal (10). 13. Reassemble parts in reverse order. It is recommended fitting the Fluid Tip (4) prior to the needle. NEVER DISPOSE OF PAINTS OR SOLVENTS INTO DRAINS. CONTACT YOUR LOCAL COUNCIL TO ARRANGE COLLECTION OR FOR DETAILS OF NEAREST REGISTERED DISPOSAL SITE. TURBINE UNIT The turbine unit only requires minimal maintenance. 1. Ensure its filter element is kept clean at all times.This is the filter underneath the main body. Disconnect the unit from the mains, turn on side and remove foam material. This can be washed out if necessary and replaced when dry. From time to time this filter will need replacing (part no.L0058). 2. The turbine bearings are sealed and lubricated for life. There is no maintenance or adjustment required. 3. Clean the turbine and hose unit with a damp cloth after use. 4. The hose is stored by locating this into the clips on the side of the main body. 5. The mains lead is stored by wrapping around the base of the unit and locating the plug in the space at the back of the unit. 6. The compartment on the top of the unit can be used for the storage of accessories. TROUBLE SHOOTING PROBLEM CAUSE ACTION REQUIRED The paint runs on the item being sprayed Paint too diluted Add undiluted material Paint volume too high Reduce the paint flow with Fluid Adjusting Screw (8) Moving too slowly Increase speed of application Gun trigger being held for too long Release Trigger earlier Gun too close Increase the distance between gun and workpiece Paint is thin or irregular Paint too diluted Add undiluted material Paint volume too low Increase the paint flow with Fluid Adjusting Screw (8) Moving too fast Reduce speed of application Gun clogged Clean the gun Gun too far away Reduce the distance between gun and workpiece No paint being produced Paint too thick Add thinner Gun clogged Clean the gun Pick up tube clogged Clean Paint Feed Tube (11) Air hose split Replace air Hose (15) Grainy paint Filter the paint Container almost empty Refill Container Gun at an angle Ensure Paint Feed Tube (11) is angled towards paint 8 L0553 (04-08) (US-FR-ES).qxd 20/6/08 2:25 pm Page 9 L0553 (04-08) (US-FR-ES).qxd 20/6/08 2:25 pm Page 9 SERVICING OF DOUBLE-INSULATED APPLIANCES In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double-insulated appliance requires extreme care and knowledge of the system, and should be done only by a qualified services personnel. Replacement parts for a double-insulated appliance must be identical to the parts they replace. This double-insulated appliance is marked with the DOUBLE-INSULATED symbol (square within a square). PLEASE NOTE: We have done all we can to ensure that used correctly and according to these instructions, this spray gun will give long and trouble free life. We accept no responsibility for damage caused by the use of incorrect or unsuitable substances, paints or fluids which have not been thinned correctly or are unsuitable for the surfaces to which they are applied, health hazards arising from lack of ventilation when working in confined spaces or failure of the equipment due to inadequate cleaning of the components after use. If in doubt, always test a small inconspicuous area first. Always read the paint manufacturer’s instructions first. Neither our guarantee nor the above statement affects your statutory rights. British Registered Design No: 2103413 German Registered Design No: 40107145.6 Benelux Registered Design No: 79476-02 US Registered Design No: D468752S Copyright & Design Right Reserved © 2008 WARRANTY This product is guaranteed for a period of 24 months against faulty manufacture and materials. It is not guaranteed for industrial or hire purposes. The guarantee does not affect your statutory rights. Earlex Inc. will accept no responsibility for the use of this product if...