Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Use the pump air regulator (K) to control the pump speed and fluid pressure. Always use the lowest pressure necessary to achieve the desired results. Higher pressures waste fluid and cause premature wear of the pump packings and spray tip. Keep the wet–cup filled with Graco Throat Seal Liquid (TSL) or other compatible solvent, to help prolong the packing life. Never allow the pump to run dry of the fluid being pumped. A dry pump will quickly accelerate to a high speed, possibly damaging itself. If your pump accelerates quickly, or is running too fast, stop it immediately and check the fluid supply. If the supply container is empty and air has been pumped into the lines, refill the supply container and prime the pump and lines with fluid, being sure to eliminate all air from the fluid system, or flush the pump as described in “Shutdown and Care”. AA2000 Spray Gun Operation Refer to the OPERATION section of manual 308–640, supplied, for installing the spray tip, adjusting the spray pattern and using the AA Plus Gun. Control the air pressure to the gun with the gun air regulator (B). Control the fluid pressure to the gun with the fluid regulator, if used. Otherwise, adjust the air pressure to the pump motor to control fluid pressure. Shutdown and Care Relieve the pressure whenever you shut off the pump. Stop the pump at the bottom of its stroke to keep fluid from drying on the exposed displacement rod and damaging throat packings. Always flush the pump with a compatible solvent before the fluid can dry on the displacement rod, and at the end of each day. If you are pumping water– based fluid, flush first with water and then with mineral spirits to protect the pump parts. If you are pumping oil–based fluids, flush with mineral spirits only. Relieve pressure and leave the mineral spirits in the pump to prevent corrosion. Manual Air Motor Lubrication To lubricate the air motor manually, first relieve the pressure. Then remove the air inlet fitting from the motor air inlet. Place 10–15 drops of oil in the inlet, reinstall the air inlet fitting and apply air to the motor. Do this daily for the best corrosion protection. 307–636 . Parts Model 230–998, Series B Includes items 1–65 Model 231–015 Includes items 1–72 Model 230–978, Series B Includes items 1–75 31 25 56 26 26 75h (REF) 16 9 10 11 8 6 7 55 5 4 3 1 35 36 37 38 5 (REF) 6 7 13 14 62 34, 12 50 4645 44 43 40 75m75n 47 48 49 39 75j 75f75a 75c 75b 75b 75h 75d 75e 75k 75l 75p75q 19 1421 (REF) 19 18 22 2324 70 71 72 17 A A B B C C NOTE: Corresponding bold letters refer to hose connections. Ref. No. 75 Fluid Regulation Kit includes items 75a–75q (used on Model 230–978 only) Ref. Nos. 70–72 are used on Models 231–015 and 230–978 only 63, 65 64 . 307–636 Parts Model 230–998, Series B Includes items 1–65 Model 231–015 Includes items 1–72 Model 230–978, Series B Includes items 1–75 REF NO. PART NO. DESCRIPTION QTY 1 162–505 UNION, swivel; 1/2 npt(m) x 1/2 npt(f) swivel 1 3 171–987 TEE, reducing, female; 3/8 npt x 1/4 npt run; 3/8 npt branch 1 4 156–823 UNION, swivel; 1/2 npt(m) x 1/4 npt(f) swivel 1 5 202–812 HOSE, air; neoprene; 1/4” (6.3 mm) ID; cpld 1/4 npt (mbe); 1.2 ft (355 mm) long 1 6 101–180 GAUGE, air pressure; 0–200 psi (0–14 bar) range 2 7 104–267 REGULATOR, air; see 307–204 for parts 2 8 158–256 UNION, swivel; 1/2 npt(m) x 3/8 npsm(f) swivel 1 9 103–347 AIR PRESSURE RELIEF VALVE 1 10 100–176 BUSHING, hex; 1/4 npt(f) x 3/8 npt(m) 1 11 108–066 TEE, pipe; 3/8 npt(m) x 3/8 npt(m) run; 3/8 npt(f) branch 1 12 104–765 PLUG, pipe, hdls; 1/8–27 npt 1 13 166–999 ELBOW, street, reducing; 1/4 npt(f) x 1/2 npt(m) 1 14 162–453 NIPPLE; 1/4 npsm x 1/4 npt 2 16 217–523 10:1 RATIO MONARK PUMP see 307–595 for parts 1 17 104–429 CAPSCREW, hex hd; 1/4–20 x 2.25” long 2 18 165–198 NIPPLE, reducing; 3/8 x 1/4 npt 1 19 206–966 HOSE, fluid; Teflon; 1/4” (6.3 mm) ID; cpld 1/4 npsm (fbe); 12.5” (310 mm) long 1 21 164–259 ELBOW, street; 3/8 npt(m) x 1/4 npt(f) 1 22 166–031 ELBOW, outlet; 3/4 npt(f) x 3/8 npt(f) 1 23 161–800 ADAPTER; 3/8 npsm x 3/4 npt (mbe) 1 24 155–665 UNION, adapter; 3/8 npt(m) x 3/8 npsm(f) 1 25 218–029 FILTER, fluid; see 307–273 for parts 1 26 210–657 BALL VALVE; 1/4 npt (mbe) 2 31 104–813 PLUG, pipe; sq hd; 3/8 npt 1 34 218–693 BASE, mounting, pump 1 35 100–933 SCREW, type F self–tapping; no. 8–32 x 3/16” 2 36 206–755 CORD, wire; 5.5” (140 mm) 2 37 164–726 PLUG, inspection hole 1 38 156–593 O–RING; nitrile rubber 1 39 101–962 SCREW, set, cup pt socket hd; 1/4–20 x 3/8” long 2 40 179–917 COVER, pail 1 43 161–395 PIN, pivot; 1/4” (6.3 mm) dia; 2” (51 mm) long 2 44 204–535 HANDLE, latch, cover 2 45 204–534 HOOK, latch, cover 2 46 158–223 WASHER; steel 2 REF NO. PART NO. DESCRIPTION QTY 47 100–063 PIN, cotter; 0.06” (1.6 mm) dia; 1/2” (12.7 mm) long 2 48 100–016 LOCKWASHER, spring; 1/4” 2 49 100–015 NUT, hex; 1/4–20 2 50 101–108 PAIL; 5 gal. (19 liter) 1 55 159–239 NIPPLE, reducing; 1/2 npt x 3/8 npt 1 56 100–721 PLUG, pipe, slotted hd; 1/4 npt 1 58 206–994 THROAT SE...
Este manual também é adequado para os modelos :Armas - 231-015 (186.29 kb)
Armas - 230-998 (186.29 kb)