Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
area. ous bodily injury. In the event that 8. Do not operate light switches, Do not injection occurs, seek medical attenengines, or similar spark producing operate tion immediately. unit if damaged during shipping, han-products in the spray area. 9. Check parts for signs of damage. dling or use. Damage may result in 9. Keep area clean and free of paint or bursting and cause injury or property Replace any damaged parts. damage. solvent containers, rags, and other 10. This spray gun is rated for 3000 psi flammable materials. (205 bar). Do not use on systems 10. Know the contents of the paints General Safety Information designed to produce more than MANUAL and solvents being sprayed. Read all 1. To reduce the risk of fire 3000 psi (205 bar). Material Safety Data Sheets (MSDS) or explosion, electrical 11. Always engage the trigger lock and container labels provided with shock, and injury to per- when not spraying. Verify the trig- the paints and solvents. Follow the sons, read and understand ger lock is functioning properly. paint and solvent manufacturer’s all instructions included safety instructions. • To lock (engage): rotate tabs on with this product. Be familiar with lock to horizontal position. the controls and the proper use of 11. Do not use materials with a flash the equipment. point less than 20°C (70°F) in or to • To unlock (disengage) to spray: clean this equipment. (Examples of rotate tabs on lock to vertical position. To reduce risk of fire or explosion: To reduce the risk of skin injection: 1. Do not aim the gun at, or spray, any per- 2 Spray Guns for Airless Paint Sprayers General Safety Information Spraying Instructions Approx. 10-12” Start Stroke Pull Trigger Release Trigger End Stroke Figure 3 - Proper Way to Trigger Spray Gun (Cont.) NOTE: If gun sprays while in the locked position follow instructions in Maintenance section for trigger lock. 12. Verify that all connections are secure before operating. Do not use pliers to tighten or loosen high pressure connections. 13. Know how to stop your unit and bleed pressure quickly. Be thoroughly familiar with the controls. Professional looking results can be obtained by following the spray tips below. 1. Keep the gun perpendicular to the surface. Always hold the gun perpendicular to the surface with the tip approximately 12” from the surface. If held at an angle (up and down or side to side), paint will build up unevenly, leave the work splotchy, and cause excessive overspray (See Figure 1). HOW TO CHANGE SPRAY TIPS: It may be necessary to change spray tips during a paint job. Follow these steps for safe, easy tip changes. 12” Figure 1 - Holding the Spray Gun 1. Depressurize and turn off unit per 1. Do not spray acids, corrosive materials, toxic chemicals, fertilizers, or manufacturer’s instructions. pesticides. Using these materials 2. Engage gun trigger lock. could result in death or serious 3. Pull red tip insert injury. out of spray base 2. Always wear appropriate gloves, and replace with differ- eye protection, and a respirator or ent tip, fully inserting tip To reduce the risk of injury: mask when painting. into base. 3. Always work in a clean environment. Do not aim the spray gun at any dust or debris. 4. Do not operate or spray near children. Keep children, pets, and visitors away from equipment and work area at all times. 5. Do not over reach or stand on an unstable support. Keep effective footing and balance at all times. 6. Stay alert and watch what you are doing. 2. Move with a smooth arm stroke Move the gun at a steady, even pace while keeping the gun perpendicular to the surface (See Figures 1 & 2). Do not fan the gun. Fanning the gun will cause excessive over- spray and uneven coverage (See Figure 2). HOW TO ATTACH ROLLER ACCESSORY: 1. Depressurize and turn off unit per manufacturer’s instructions. 2. Engage gun trigger lock. 3. Remove spray base, tip, seal and washer assembly. 4. Attach roller accessory (AL2275 Thin Coat Thin Coat Heavy Coat Over- spray Over- spray Figure 2 -Result of Flexing Wrist While Spraying INCORRECT shown) to air- less spray gun. If needed use 7. Do not operate the equipment when fatigued or under the influ ence of drugs or alcohol. thread adapter and washer between roller and spray gun as shown. INTERMITTENT USE If you are spraying and decide to stop for several minutes, lock the spray gun trigger and submerge the tip in a container of suitable solvent (See Figure 4). This will prevent paint from hardening in the tiny spray opening and clogging the tip. Be sure to release the pressure in the system and turn the unit off according to the manufacturer’s instructions. CLEARING CLOGS REVERSIBLE TIP: (Included) 1. Rotate the tip to the clean position (See Figure 5). FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SERIOUS INJURY INCLUDING DEATH. Preparation Airless painting systems, unlike most other power tools, require additional care to ensure proper working order. CONSULT YOUR AIRLESS PAINT ...
Este manual também é adequado para os modelos :Armas - AL1860 - METAL (1.4 mb)