Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
Disengage gun trigger safety. 5. Hold gun against grounded metal flushing pail. Trigger gun and increase fluid pressure 1/2 turn. Flush 1 minute. 6. Inspect for leaks. Do not stop leaks with hand or a rag! If leaks occur, perform Pressure Relief Procedure, page 8. Tighten fittings. Perform Startup, steps 1 - 5. If no leaks, proceed to step 7. 7. Place pump in paint pail. 8. Trigger gun again into flushing pail until paint appears. Move gun to paint pail and trigger for 20 seconds. Set gun safety ON. Assemble tip and guard, see instructions on next page. ti4266a ti4266a 1/2 15sec. ti14845a ti10167a ti4271a 1/2 ti13243a PAINT ti2714a ti13029a ti10166a Switch Tip Installation 3A0156A 11 Switch Tip Installation 1. Use spray tip (A) to insert OneSeal™ (B) into guard (C). 2. Insert Switch Tip. 3. Screw assembly onto gun. Tighten. Spray 1. Spray test pattern. Increase pressure to eliminate heavy edges. Use smaller tip size if pressure adjustment can not eliminate heavy edges. 2. Hold gun perpendicular, 10-12 in. (25-30 cm) from surface. Spray back and forth. Overlap by 50%. Trigger gun after moving and release before stopping. Clearing Tip Clog 1. Release trigger, put safety ON. Rotate SwitchTip. Take safety OFF. Trigger gun to clear clog. Never point gun at your hand or into a rag! 2. Put safety ON. Return SwitchTip to original position. Take safety OFF and continue spraying. ti13023a C B A ti13024a ti2710a ti13030a ti13025a ti10166a ti13033a ti10167a ti10166a ti13034a ti10167a WatchDog™ Protection System (Not Available on All Units) WatchDog™ Protection System (Not Available on All Units) Pump stops automatically when material pail is empty. To Activate: 1. Perform Startup. ti7398a 2. Premium units with digital display: Turn WatchDog switch ON and WD ON displays. EMPTY displays/flashes and pump stops when Watchdog protection system detects an empty material pail. ti6224a 3. Turn WatchDog switch OFF. Add material or reprime sprayer. Turn pump switch OFF and ON to reset WatchDog protection system. Turn WatchDog switch back ON to continue to monitor material level. ti7399a ............A Fast Flush To flush the hose and gun at an accelerated speed, perform the following steps: 1. Perform steps 1 -3 of Cleanup, page 16. 2. Hold gun trigger in and turn prime valve down to DRAIN position and then over to FAST FLUSH. ti14849a 3. Continue flushing system until fluid appears clear. 12 3A0156A Hose Reel (Not Available on All Units) 3A0156A 13 Hose Reel (Not Available on All Units) 1. Make sure hose is routed through hose guide. 2. Lift and turn pivot lock 90° to unlock hose reel. Pull on hose to remove it from hose reel. 3. Pull reel handle up and turn clockwise to reel in hose. NOTE: The hose reel can be locked into two positions: Usage (A) and Storage (B). Be sure to keep your head clear of hose reel while winding up hose. ti13504a ti13501a ti13503a ti13502a (A) (B) ti13563a Digital Tracking System (Not Available on All Units) 14 3A0156A Digital Tracking System (Not Available on All Units) Operation Main Menu Short press to move to next display. Press and hold (5 seconds) to change units or reset data. 1. Turn pressure to lowest setting. Trigger gun to relieve pressure. Turn prime valve down to DRAIN position. 2. Turn power ON. Pressure display appears. Dashes will not appear unless pressure is less than 200 psi (14 bar, 1,4 MPa). Change Display Units Press and hold DTS button for 5 seconds to change pressure units (psi, bar, MPa) to desired units. Selection of bar or MPa changes gallons to liters x 10. To change display units DTS must be in pressure display mode and pressure must be at zero. Job Gallons 1. Short press DTS button to move to Job Gallons (or liters x 10). NOTE: JOB scrolls past, then the number of gallons sprayed above 1000 psi (70 bar, 7 MPa) displays. 2. Press and hold to reset to zero. Lifetime Gallons 1. Short press DTS button to move to Lifetime Gallons (or liters x 10). NOTE: LIFE scrolls briefly, then the number of gallons sprayed above 1000 psi (70 bar, 7 MPa) displays. ti13605a - ti14842a ti13243a ti4266a psi ti13621a Psi bar Psi MPa ti13620a ti13604a Psi ti13620a ti13610a ti13612a OR ti13601a ti13611a ti13617a Digital Tracking System (Not Available on All Units) Secondary Menu - Stored Data and WatchDog Pump Protection Modes 1. Perform Pressure Relief, steps 1 - 4 if they have not already been done. 2. Turn power switch on while holding DTS button down. ti13605a ti4266a 3. SERIAL NUMBER scrolls past and then serial number (e.g. 00001) displays. ti13622a ti7362a 4. Short press DTS button and MOTOR HOURS scrolls past and then total motor run hours are displayed. 7. Short press DTS button. W-DOG scrolls past then OFF displays if watchdog switch is OFF. ON displays if Watchdog switch is ON. ti13608a ti13626a ti13614a 8. Press and hold (8 seconds) DTS button to move to WatchDog Trigger % menu. Continue to hold DTS button and Watchdog can be set to trigger at 30, 40, 50, or 60% of current sprayer press...
Este manual também é adequado para os modelos :Armas - 1095 Premium Hi (2.76 mb)