Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
**The /&@num Operating Air Pressure indicates the maxi- mum air pressure the air cap supplied with this gun was designed to operate at or below to comply with California Wood Rule 7 736. To guarantee compliance to rule 1136, the gun must be used with Air Regulator Part No. 110-776. This regulator limits the operating pressure to 10 psi (0.7 bar), using an air supply pressure of 100 psi (7 bar). U.S. Patent Nos. 3843,052; 4,386,739 United Kingdom Patent No. 2 111 406 B Patented 1984 Canada Brevete 1984 French Patent No. 82-21202 Foreign Patents Pending GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441 OCOPYRIGHT 1988, GRACO INC. Table of Contents SafetyWarnings ............................... 3 Installation Ventilate the Spray Booth ..................... 6 Required Accessories ........................ 6 Connect the Air Line ......................... 7 Connect the Fluid Line ....................... 7 Grounding .................................. 7 Operation How Air-Assisted Airless Spray Gun Operates ... 7 Select A Spray Tip ........................... 8 Install a Spray Tip ............................ 8 Adjust the Spray Pattern and Apply the Fluid .... 8 Flush the Gun Daily ......................... 10 Clean the Spray Gun and System Daily ........ 10 Troubleshooting .............................. Service Air Valve Service ............................ Fluid Packing Replacement .................. Parts ........................................ Optional Parts ............................... Accessories ................................. Spray Tip Selection Charts .................... Technical Data ............................... Dimensions .................................. Warranty ............................ 11 12 12 14 15 16 18 19 19 Back Cover 2 307-947 WARNINGS High Pressure Spray Can Cause Serious Injury. For Professional Use Only. Observe All Warnings. Read and understand all instruction manuals before operating equipment. FLUID INJECTION HAZARD General Safety This equipment generates very high fluid pressure. Spray from the gun, leaks or ruptured components can inject fluid through your skin and into your body and cause extremely serious injury, including the need for amputation. Also, fluid injected or splashed into the eyes or on the skin can cause serious dam- age. Never point the spray gun at anyone or at any part of the body. Never put hand or fingers over the spray tip. Never try to stop or deflect leaks with your hand or body. Never try to “blow back” paint; this is not an air spray gun. Always follow the Pressure Relief Procedure, at right, before cleaning or removing the spray tip or servicing any system equipment. Check operation of all equipment safety devices before each use. Medical Alert -Airless Spray Wounds If any fluid appears to penetrate your skin, get emer- gency medical care at once. Do not treat as a sim- ple cut. Tell the doctor exactly what fluid was injected. NOTE TO PHYSICIAN: Injection into the skin is a traumatic injury. It is important to treat the injury surgically as soon as possible. Do not delay treat- ment to research toxicity. Toxicity is a concern with some exotic coatings injected directly into the blood stream. Consultation with a plastic surgeon or reconstructive hand surgeon may be advisable. Spray Gun Safety Devices Be sure all gun safety devices are operating properly before each use. Do not remove or modify any part of the gun; this can cause a malfunction and result in serious injury. Safefy Latch Whenever you stop spraying, even for a moment, always set the gun safety latch in the closed or “on safe” position, making the gun inoperative. See Fig. 3, page 8. Failure to set the safety latch can result in accidental triggering of the gun. Diffuser The gun diffuser breaks up spray and reduces the risk of fluid injection when the tip is not installed. Check diffuser operation regularly. Follow the Pres- sure Relief Procedure, below, then remove the spray tip. Aim the gun into a grounded metal pail, holding the gun firmly to the pail. Using the lowest possible pressure, trigger the gun. If the fluid emitted is not diffused into an irregular stream, replace the diffuser immediately. Spray Tip Safety Use extreme caution when cleaning or changing spray tips. If the spray tip clogs while spraying, engage the gun safety latch immediately. Always fol- low the Pressure Relief Procedure, below, and then remove the spray tip to clean it, Never wipe off build-up around the spray tip or air cap until pressure is fully relieved and the gun safety latch is engaged. Pressure Relief Procedure To reduce the risk of serious injury, including fluid injection, splashing in the eyes or on skin, or injury from moving parts, always follow this procedure whenever pump is shut off, when checking or servic- ing any part of system, when installing or changing spray tips and whenever you stop spraying. 1. Engage the spray gun safety latch. 2. Shut off the power to the pump. 3. Close the ble...