Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. HVLP Spray Gun Attention: Campbell Hausfeld recommends that servicing other than that shown in the instruction manual should be performed by an authorized service facility. Description High volume, low pressure (HVLP) paint spray ers are de signed to de liv er a fine finish with low overspray. The sprayer can be used to apply various acrylics, stains, sealers, lacquers, latexes, and primers. This unit can be used for painting cabinets, fur ni ture, ma chin ery, equip ment, walls and trim work. Sprayers of this type are not recommended for au to mo tive final coat. This por ta ble unit is an ideal alternative to con ven tional spray guns. The HVLP’s high transfer efficiency pro vides pro fes sion al re sults with much less material waste and en viron men tal con tam i na tion than other con ven tion al spray paint ing sys tems. Unpacking When unpacking the sprayer, inspect carefully for any damage that may have occurred during transit. Make sure any loose fittings, bolts, etc., are tightened before putting sprayer into service. Each sprayer has been tested before shipment. NOTE: The packing nut may need additional adjustment due to the packing material relaxing during shipment. The fluid used for testing the sprayer has been drained, but some of this fluid will remain in the spray gun. This fluid should be flushed from the spray gun to prevent contamination of the coating material. Use a solvent compatible with the coating to be sprayed. Table Of Contents Description . . . . . . . . . . . . . . . . . . . . 1 Unpacking. . . . . . . . . . . . . . . . . . . . . 1 General Safety Information. . . . . . . 1 Setup. . . . . . . . . . . . . . . . . . . . . . . .2-3 Operation. . . . . . . . . . . . . . . . . . . . . 4 Maintenance. . . . . . . . . . . . . . . . . .4-5 Troubleshooting. . . . . . . . . . . . . . . . 6 Warranty. . . . . . . . . . . . . . . . . . . . . 10 Locking Lever For Quick-Release Paint Cup Air Flow Control Material Flow Control Knob 1 Quart Cup Oval To Round Pattern Ad just ment Quick Connect Fitting Figure 1 - Features General Safety Danger means a death or serious injury if the warning is ignored. ! DANGER hazard that will cause ! WARNING Warning means a hazard that could cause death or serious injury if the warning is ignored. Caution means a ! CAUTION hazard that may cause minor or moderate injury if the warning is ignored. It also may mean a hazard that will only cause damage to property. Notice means any NOTICE additional information pertaining to the product or its proper usage. Read all instructions and safety precautions before operating the unit. Risk ! WARNING of fire or explosion! Solvent and paint fumes can explode or ignite, causing severe injury and property damage. Paints and solvents containing HALOGENATED HYDROCARBONS can react explosively with aluminum. Always check the product’s label before using these materials in the unit. Make sure the room is well-ventilated. Avoid all ignition sources, such as static electricity sparks, open flames, hot objects, sparks from connecting and disconnecting power cords, and working light switches. Follow the material and solvent manufacturers’ safety precautions and warnings. Do not use liquids with flash points less than 100 degrees Fahrenheit (38 degrees Celsius). Do not carry TURBINE while spraying. Keep the turbine at the maximum distance from the spraying area. Static electricity can be produced by HVLP spraying. Make sure any electrically conductive object being sprayed is grounded to prevent static sparking. The sprayer is grounded through the electric cord. If an extension cord is necessary, the cord must be a grounded, 115 volt, three wire type cord. ©2007 Campbell Hausfeld/ Scott Fetzer IN206701AV 9/07 For parts, product & service information visit Operating Instructions and Parts Manual General Safety (continued) Hazardous vapors: Paints, solvents, insecticides, and other materials may be harmful if inhaled, causing severe nausea, fainting, or poisoning. Use a respirator or mask whenever there is a chance that vapors may be inhaled. Read all instructions with the mask to ensure that the mask will provide the necessary protection against the inhalation of harmful vapors. NEVER point the spray gun at any part of the body, or at anyone else. ! CAUTION Tipping the gun causes the gun to clog. Dried spray material also clogs the pressure delivery tube and fittings. The spray gun does not function when clogging occurs. When not in use, be sure to disconnect the hose and place the gun on a solid, level surface to avoid tipping. Components (1) Gun - fully assembled, with all purpose needle/nozzle installed Setup NEEDLE AND NOZZLE ASSEMBLY 1. Use Chart 1 to determine the proper size nozzle and needle for the material to be applied. T...
Este manual também é adequado para os modelos :Armas - IN206701AV (1.89 mb)
Armas - HVLP (1.89 mb)